Bedienungsanleitung Soehnle Airfresh Clean 400 (Seite 14 von 138) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch)

804713

Zoom out

Zoom in

Vorherige Seite

1/138

Nächste Seite

7. Daily use and operation

PM 2,5 sensor and LED ring

The current air quality is continuously determined

by Airfresh Clean 400 in the form of the PM 2.5

value.

The PM 2.5 value is the fine dust load

(50% of particles approx. 2.5μm) in μg/m

The illuminated LED ring on the upper side

indicates the current level of fine dust pollution

caused by different colours:

RED = high load (>50 µg/m³)

PINK = medium load (20 - 50 µg/m³)

LILA = low load (10 - 20 µg/m³)

BLUE = no load (0 - 10 µg/m³)

Please remove the protective ap in front of the PM2.5 sensor

other foreign bodies to come into contact with the sensor.

Switching on and off

Press the ON/OFF button (L) to turn the

Airfresh Clean 400 on or off. The ON/OFF

control lamp lights up.

First press:

Device is switched on

Press twice:

Activates the automatic mode

Press the third time:

Deactivates the automatic mode.

Press four times:

Device is switched off

The control lamps light up accordingly.

Automatic mode

By pressing the (L) button as

described

above, the Airfresh Clean 400 is also set to

automatic mode. In this mode, the unit

automatically adjusts the fan speed in

relation to the air quality in the room. This

ensures you always get the best possible

air quality. The control lamp for AUTO

lights up.

Setting the operating time

Press button (I) to set the desired oper-

ating time. Choose between 2, 4 and 8

hours. The control lamp lights up ac-

cordingly. The device switches off auto-

matically after the time has elapsed. If

no operating time has been selected

(no indicator light is lit), the Airfresh

Clean 400 runs in continuous operation.

Changing the fan speed

Press button (K) to select the fan speed

and thus the desired intensity of air

discharge:

Low (I) - Medium (II) - High (III) -

Turbo (all indicator lights on)

UV-C lamp and night mode

Press button (J) once to switch on the

UV-C lamp inside the Airfresh Clean 400

(UV-C control lamp lights up). Press again

to activate the night mode without

switching off the UV-C lamp (UV-C con-

trol lamp lights up, NIGHT control lamp

flashes). By further pressing button (J)

you can switch off the UV-C lamp (UV-C

control lamp is off, NIGHT control lamp

flashes) or switch both off (UV-C control

lamp is off, NIGHT control lamp is off).

Night mode

In night mode, you can run the Airfresh

Clean 400 without being disturbed by

additional light sources. If you activate

the night mode, all indicator lights

the device are switched off after 10 sec-

onds without the device being switched

off. Previously made settings for operat-

ing time and fan speed are retained. The

activation of the night mode is initiated

by a flashing of the control lamp before

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Soehnle Airfresh Clean 400 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info