Bedienungsanleitung Solac AS3260 (Seite 13 von 78) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

488728

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

CLEANING AND CONSERVATION 13

SAFETY THERMOSTAT

The system has a safety thermostat. If for any reason the vacuum cleaner should overheat,

the thermostat will automatically shut off the appliance. If this should happen:

1 Press the on/off switch (5) and unplug the appliance from the mains.

2 Check that the air intakes and outlets are not blocked. If they are blocked, get rid of

the cause of the blockage.

3 Empty the dust container (outer and inner chamber). See the next section “Cleaning

and Conservation”.

) If the automatic shut-off was due to the motor overheating, wait for about one hour for

the appliance to cool before turning it on again. You can reduce the waiting time by

placing the appliance in a cool or well-ventilated place to allow the heat to dissipate.

CLEANING AND CONSERVATION

EMPTYING THE DUST CONTAINER (19)

) The dust container (19) has a maximum level mark. Check the dust does not exceed

that level.

1 Turn the carry handle (15) backwards to make the dust container (19) accessible.

2 Press the release button (24). This releases the dust container. (fig. 4).

3 Remove the dust container and hold it over the waste bin. Press the button (23) on the

container (fig. 5) to empty the contents into the bin.

4 Turn the dust container cover (21) anti-clockwise and remove the inner chamber (20)

(fig. 6). Empty the contents.

5 Clean the inner chamber (20) and dust container with a brush and wet cloth.

) Check that the washed elements are completely dry before putting them back

together.

) Never immerse the inner chamber in water or any other liquid, nor put it in the

dishwasher. Do not use abrasive products or solvents.

6 Put the inner chamber back into the container (check that the marks coincide).

7 Place the container cover (21) on the mark and turn it clockwise to the mark .

8 Put the dust container back inside the appliance. Push the container towards the

appliance body while pressing the release button (24). This blocks the container.

CLEANING THE MOTOR PROTECTION FILTER (26)

) It is advisable to inspect the motor protection filter from time to time, to ensure that it is

operating correctly.

) Once or twice a year, or if a reduction in suction power is detected, clean the protection

filter. To do so:

1 Remove the dust container. See the previous section “Emptying the dust container

(19)”.

2 Remove the filter cover (25) by pressing the upper tab. Remove the grille (27) (fig. 7).

3 Remove the protection filter (26) from the grille (27) (fig. 7).

4 Wash the filter with tap water and leave it to dry completely.

) The filter can be washed with warm water (max. 40 ºC). Leave it to dry for 24 hours

before replacing it.

5 Put the grille and motor protection filter back in their housing.

) Never use the vacuum cleaner without the motor protection filter.

AS3260.book Page 13 Thursday, January 14, 2010 1:29 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Solac AS3260 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info