718606
11
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
PROBLEM CAUSE SOLUTION
The appliance does not work. The appliance is not connected to the mains. Plug in and press the switch.
Check the cable and the Plug
No or delayed response in several trials of
pressing on function key on the panel
Appliance is under an electromagnetic interference
Dirt over the panel
Unplug the appliance. Restart after fewminutes
Clean the panel with the cloth provided
The coffee is not hot enough. The cups have not been preheated.
The brewing unit is too cold.
Rinse the appliance at least 3 times before
making the coffee.
The coffee cannot come out from spout. Empty system function maybe used before. Press the hot water button until water can come
out from spout.
The rst cup of coffee is poor quality. The rst run of grinder does not pour sufcient
quantity coffee power into the brewing unit.
Throw the coffee away. The other coffees will
always be of good quality.
Coffee has no cream. Coffee bean is not fresh. Change or using appropriate brand of coffee
bean.
The touch buttons are not sensitive Not pressing the touch button from the front
direction of the appliance
Press the lower bottom part of the icon of the
touch button from the front direction of the
appliance.
The appliance takes too long time to warm
up.
Excessive scale has built up. Descale the appliance.
The water tank is removed / the water
level is very low in the water tank but Icon
(A) have no alert.
The area near the water tank connector is wet. Wipe the water around the water tank connector
Internal drip tray is lled with a lot of water. Coffee powder too ne which block the water to
come out.
Adjust the coffee neness to bigger dot during
grinder operation.
Coffee is delivered too slowly or a drop at
a time.
Coffee powder too ne which block the water to
come out.
Adjust the coffee neness to bigger dot during
grinder operation.
Lack of bean indicator (B) ashes but
there is still a lot of coffee bean inside the
container (11).
Internal coffee powder outlet is blocked. To follow the steps of section (Cleaning coffee
powder outlet).
Milk foam cannot be recreated by steam
nozzle
The nozzle is dirty and hole on nozzle cover (6) or
metal tube (5) was blocked by milk residual
To follow the steps of section (DAILY CLEANING
OF THE APPLIANCE) to clean steam nozzle
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Solac CA4810 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info