Bedienungsanleitung Solac SW8230 - Cotton 16.0 (Seite 12 von 24) (Englisch, Französisch, Portugiesisch, Spanisch)

718539

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Features

1. Selection of stitch pattern

- Rotate the pattern selection dial to select the 16

stitch patterns you wanted.

- CAUTION: Before you change the stitch pattern,

please turn off the switch and turn the hand wheel

to raise the needle all the way up so it doesn’t get

stuck and bent.

- CAUTION: Changing the stitch pattern is not

allowed when the machine is running; otherwise, the

needle and/or machine may damage.

2. Reverse sewing

- When the machine is running, press down and

hold the reverse sewing button when you want to do

reverse sewing; release the button, the machine is

doing normal sewing.

3. Setting the sewing speed

- Slide the power switch to “I” or “II” position.

- I: Low speed

- II. High speed

4. Working lamp

- If additional light is needed, press the light switch

to turn the light “ON”. Press the switch again to turn

it “OFF”.

5. Thread cutter

- The machine has a thread cutter on the central left

side of the machine, it can cut off the thread after

sewing or winding thread.

6. Sewing sleeves

- This sewing machine has been designed to sew

sleeves or any narrow openings in garment. Pull out

the drawer and position the garment over the sewing

arm if you want to sew the sleeves.

7. Manual buttonhole

- 1. Put the cloth under the presser foot and lower the presser foot on

the cloth where you need to sew buttonhole, then choose the 15

stitch.

- 2. Turn on the switch and sew 5-6 stitch in low speed, then turn off the

switch (Fig.15).

- 3. Choose the 16

stitch, turn on switch and sew on the cloth in suit-

able length, then turn off switch. Note that try to keep sewed stitch in

straight line. (Fig.16)

- 4. Choose the 15

stitch, then turn on switch and sew 5-6 stitch in low

speed, then turn off switch (Fig.17)

- 5. Raise the presser foot, rotating the cloth for 180º (Fig.18)

- Choose the 16

stitch, then turn on switch and sew till buttonhole is

fully sewed. (Fig.19)

8. Drawer.

- This drawer is an accessory storage compartment, which can be slide

out and you can store spare bobbins, needles, etc. in it.

Winding the bobbin

- 1. Put a spool of thread on spool pin. (Fig.20)

- 2. Guide the thread through the bobbin winder tension disk on the

upper side of the machine. (Fig.21)

- 3. Put the bobbin on the bobbin winder pin, wind thread clockwise

around bobbin several times. (Fig. 22)

- 4. Push bobbin to the left. (Fig.23)

- 5. Switch on the machine to start winding. (Fig.24)

- 6. Switch off the machine to stop winding after appropriate volume of

thread you wanted had winded on bobbin.

- 7. Push bobbin away from bobbin winder stop, take bobbin off the pin

and cut the thread. (Fig.25)

Caution

- During bobbin winding, no thread on the needle/take up lever is al-

lowed. Please take thread off from it before bobbing winding.

- Before bobbin winding, raise the presser foot.

Adjusting stitching

- 1. As shown in the picture A, normal stitching shall have top and bot-

tom threading evenly, neither over tight nor loose.

- 2. If the bottom threading looks like a straight line (Fig.B), which indi-

cates the top thread is too loose. Please turn upper thread tension dial

to direction with bigger number to increase pressure until the stitching

return to norma.

- 3. If the top thread looks like straight line (Fig.C), which indicates an

over-tight top thread. Please turn the upper thread tension dial to the

direction with smaller number to reduce pressure until the stitching

back to normal.

Applicable cloth for sewing

Cloth

Sewing

presentation

Cotton /

Linen

Silk /

Wool

Polyester Elastic

Fabric speci-

cation

Regular √ √ √ Δ

Thick √ √ √ Δ

Thin √ Χ Χ Χ

Hard √ √ √ Δ

Soft Χ Χ Χ Χ

Sewing effective:

• √: means easy to sew

• Χ: means difcult to sew

• Δ: means not smooth to sew

Note:

1. The denition of the fabric thickness:

• Thin (fabric): Two layers of the fabric thickness <0.35mm

• Thick (fabric): two layers of the fabric thickness >0.8mm

• Regular (fabric): two layers of the fabric thickness ≥0.35mm and

≤0.8mm

2. The denition of elastic cloth:

• If the cloth, which size is “100mmx30mm”, is extending to or

over 106 mm under 0.5Kg tension force, then the cloth is de-

ned elastic, otherwise it is inelastic.

3. Hard fabric: such as Jeans, ne canvas, etc.

4. Soft fabric: such as towel, duster, etc.

Once you have nished using the appliance:

- Turn the appliance off, using the on/off switch.

- Stop the appliance using the on/off switch.

- Unplug the appliance from the mains.

- Put the cable back in the cable housing.

- Clean the appliance.

Carry handle/s:

- This appliance has a handle on the upper part of the body, which facili-

tates comfortable transportation.

Safety thermal protector:

- The appliance has a safety device, which protects the appliance from

overheating.

- If the appliance turns itself off and does not switch itself on again,

disconnect it from the mains supply, and wait for approximately 15

minutes before reconnecting. If the machine does not start again seek

authorised technical assistance.

Cleaning

- Disconnect the appliance from the mains and allow it to cool before

undertaking any cleaning task.

- Clean the equipment with a damp cloth with a few drops of washing-up

Solac SW8230 - Cotton 16.0 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info