Bedienungsanleitung Solis Vario Temp Kettle - 5516 (Seite 38 von 53) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

708738

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

7574

GB GB



CONTROL BUTTONS

ON THE CONTROL PANEL



CONTROL BUTTONS

a Temperature button 70°

b Temperature button 80°

c Temperature button 90°

d Temperature button 100°

e Warm-keeping button KEEP WARM

f ON/OFF button and quick start button to heat up to 100 °C

Note: every press of a button is accompanied by a signal tone.



BEFORE FIRST USE

The kettle has to be cleaned prior to its ﬁrst use. Proceed as following:

1. Place the unit base on a heat- and waterproof, clean, dry, solid and even work-

top close to a power outlet and out of the reach of children. Unroll the power

cord of the unit base completely and place it in a way that the appliance can

not be dragged down by the cord.

2. Take the kettle off the base and press the lid release button to open the lid.

3. Wipe the kettle´s and lid´s interior and exterior clean with a soft, damp cloth

and dry everything off.

4. Fill the kettle with cold tap water up to the MAX marking on the water display.

a fb ec

Caution: The MAX marking in the kettle must never be exceeded, otherwise

boiling water might splash out! The maximum capacity is 1,7 litres. Likewise,

the MIN marking (0,5 litres) must never be undercut, otherwise the overheating

protection is triggered and the appliance automatically switches off.

5. Close the lid again by pressing it down until it snaps in. Caution: the lid must

always be closed during boiling.

6. If necessary, dry the outside of the kettle as well as the kettle bottom. Place the

kettle on the dry appliance base.

7. Connect the power plug to a suitable power outlet, the power cord has to be

completely unwound.

8. All control buttons light up brieﬂy and then a two-time signal tone sounds while

all control buttons turn off, except for the temperature 100 °C button, which is

blinking blue, and the ON/OFF button which is lighting green. The blue blinking

temperature button and the green lighting ON/OFF button indicate that the

appliance is in standby mode.

9. Initially press the temperature 100 °C button and then the ON/OFF button to

heat up the water to 100 °C (or press solely the ON/OFF button to do a quick

start). During boiling the temperature 100 °C button lights up constantly blue

and the ON/OFF button lights red.

10. Wait until the water is boiling. At the end of the boiling process you will hear

a two-time signal tone and the control light of the ON/OFF button will light

green. The appliance will turn off automatically.

11. Pour the water carefully out the spout while keeping the lid closed.

12. Let the appliance cool down and then ﬁll it again with cold tap water. To do

this open the lid and take the kettle off the unit base.

13. Afterwards put the ﬁlled kettle (with dry exterior) back onto the base and close

the lid.

14. Repeat the boiling process a second time and pour out the water again.

15. Your appliance is now ready to use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Solis Vario Temp Kettle - 5516 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info