Bedienungsanleitung Solo 106 (Seite 26 von 100) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

634115

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Insert the locking pin to lock the gearbox

drive shaft. Centre the appropriate cutter on

the boss washer (5) and position onto the

gearbox drive shaft. Locate the deep disc (6)

and secure with the disk spring (7) and lock

nut (8) Please note: Left hand thread! Tighten

the nut anti-clockwise.

4. Note: The thrust piece has been incorrectly

fitted if the cutter can still be turned, even if

the nut has been fully tightened and the gear-

box drive shaft has been locked. In such cases,

repeat the installation correctly.

5.7

Line head installation (models 106L and 106R)

1. Note: When mounting the line head, the

boss washer (Fig. 13.5), the deep dish (Fig.

13.6), the disk spring (Fig. 13.7) and the lock

nut (Fig. 13.8) will not be required.

FIG. 14

2. Position the clamp (2) in the correct way

(with the angled edge pointing towards the

gearbox) on the gearbox output shaft (1).

Turn the gearbox input shaft with the clamp

so that the recess for the locking pin (3) is

flush with the recess in the winding protection

(4) or the gearbox housing. Insert the locking

pin to lock the gearbox drive shaft. The com-

plete line head with additional line winding

protection (A) is threaded onto the gearbox

drive shaft and against the thrust piece. Please

note: Left hand thread! Tighten the line head

clockwise.

3. The spacer (5) and the line trimmer

blade (6) must be mounted to the

contact protection shield.

5.8 Shoulder strap

1. Properly locate the shoulder strap (part of

the standard delivery of model 106, optional

accessory for model 105). To install the shoul-

der strap on models 105, 106L and 106R, two

plastic clips are mounted on the handle tube

between the function handle with throttle

lever and the loop handle. Hook the shoulder

strap into the plastic clips. When using the

motor scythe on the r.h. side of your body,

position the single shoulder strap over your

l.h. shoulder, so that, after adjusting the strap

length, the strap hook is located at your r.h.

hip. When using the motor scythe on your l.h.

side (only with the loop handle and the safety

end-stop installed pointing to the right), pro-

ceed vice-versa. The motor scythe cannot be

precisely balanced via the shoulder strap when

using the loop handle. Continue to guide the

motor scythe via the loop handle.

2. Install the shoulder strap for model 106B as

follows:

3. Note: Always lead the motor scythe with

the two-handed bike handle on the r.h. side of

the body.

4. Before commencing work, adjust the shoul-

der strap and handle according to the opera-

tor’s body size.

Position the single shoulder strap over your l.h.

shoulder, so that, after adjusting the strap

length, the strap hook is located at your r.h. hip.

After hook (1) has been hooked into the

shoulder strap rail on the protection tube,

balance the motor scythe with fitted cutter so,

that the cutter just touches the ground, with

out touching the suspended motor scythe

FIG. 15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Solo 106 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info