Bedienungsanleitung Solo 106 (Seite 29 von 100) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

634115

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

7.6 If the motor run

Once the engine runs, briefly pull the throttle

back to release the half throttle detent. Re-

lease the throttle lever again to allow the

engine to run at idle speed. Now you can com-

mence working.

7.7 Turning off the motor

1. Release the throttle and push the stop

switch to ”STOP”.

Due to the centrifugal clutch, the cutters will

run on for a short time, even if you release the

throttle. Ensure the cutter has fully stopped

before storing the machine.

8. Using the motor scythe

8.1 Adjusting cutting line

1. Subject to the fitted cutter, only use the

motor scythe to mow grass, weeds, rough

growth, shrubs, undergrowth, brush, etc.

Never use the motor scythe for any other pur-

poses. Always fit a contact protection shield,

which is suitable for the equipment and the

cutter. Cutter heads with plastic lines are suit-

able for a soft cut, e.g. to cleanly cut around

trees and posts. Approach the growth with the

machine set to idle and then use full throttle.

Never raise the engine speed without load.

FIG. 21

4. Immediately switch off the engine when

you notice irregularities, e.g. if the cutter or

contact protection shield becomes blocked.

Brake the cutter by pushing it onto the

ground, until it has completely stopped. Pull

the spark plug cap, and remove grass, debris,

etc. from the cutter support. Check the entire

machine to ensure its operational condition.

5. When using the line head (model 105, 106L

and 106R; 106B [option]), only work with an

approved line length. If the contact protection

shield is properly fitted, cutting lines will al-

ways be trimmed to the permissible length

(trimming blade integrated into the contact

protection shield). Lines left too long can

cause injury and will overload the engine,

which may cause damage.

6. When refitting units previously equipped

with metal tools to line heads (model 106), the

standard contact protection shield must there-

fore be supplemented with appropriate sup-

plementary components (spacer and line trim-

ming blade).

2. Dip the cutter 2/3 into the growth and use

the equipment like a scythe by stepping for-

ward in small steps and cutting from side to

side.

3. Use the motor scythe at full throttle to ob-

tain the best results. Never operate in the

slipping range of the clutch. Consequential

losses through abuse of the equipment are

excluded from the guarantee.

1. When using a semi-automatic line head:

2. Whilst the motor scythe is running without

load, but with rotating line head, lightly push

the line head several times onto ground with

growth cover. The cutting line will be dis-

pensed in stages. With each action, approx. 30

mm line will be dispensed. Any excess length

will be corrected by the line trimming blade.

3. When the cutting line is fully spent, you can

replace it with line available under part no.

6900997 (accessory).

FIG. 22

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Solo 106 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info