Bedienungsanleitung Solo 462 (Seite 21 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

655623

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

2 Preparing the device for use / 3 Mixing spraying agents and filling the spraying agent tank

ENGLISH 7

2 Preparing the device for use

2.1 Assembly

The pressure sprayer is dismantled before it is

dispatched. It must be fully reassembled again

before it is used.

Installation of the nozzle attachment

(only for models 461 and 462):

x Firmly screw the nozzle attachment (Fig. 2,

Pos. 1) with the O-Ring (10x2 mm) hand-tight

onto the spray tube. Do not use any tools!

Installation of the high-pressure hose:

x Push the threaded collar (Fig. 2, Pos. 2) onto the

high-pressure hose (Fig. 2, Pos. 3).

x Push the hose completely onto the provided

connector of the red-flanged housing, by using

strong pressure and turning the hose.

x Secure the hose by screwing on the threaded

collar (hand-tight, do not use any tools!).

Installation of the spray tube:

x Fasten the threaded collar (Fig. 2, Pos. 4) on

straight and firmly screw the spray tube (6) with

O-ring (16x3 mm) hand-tight onto the shut-off

valve. Do not use any tools!

When your work is completed, the spray tube

should be fitted into the holding clamp at the pump

handle (3).

Please put the nozzle completely up (Fig. 1).

Installation of the pressure gauge

(depending on the model):

x Unscrew the black threaded collar from the

shut-off valve.

x Screw the black threaded collar of the pressure

gauge accessory kit onto the shut-off valve.

x Insert the O-ring into the threaded collar and

screw the pressure gauge hand-tight into the

threaded collar. Do not use any tools!

2.2 Spray nozzle and filter element

At the factory, a red flat jet nozzle 04-F110 is

assembled as the standard spray nozzle.

Delivery rate: See section 10

A filter element is fitted in the elbow piece up-

stream of the spray nozzle (Fig. 2, within Pos. 1).

Only the spray nozzles listed in section 10 and the

genuine filter element (part no.: 40 74 922 25,

mesh aperture: 0.8 mm [0.031"]) must be used in

this pressure sprayer.

Changing spray nozzles and filter element:

See section 5.3

2.3 Carrying strap

Thread both ends of the carrying strap through the

slits provided on the red flanged housing (Fig. 4).

Use the sliding clip to adjust the carrying strap to

the required length.

2.4 Trial run

At first start-up, at the start of the spraying season

and in frequent use at least once a month, perform

a trial run according to section 5.1 to check the

entire device.

3 Mixing spraying agents and

filling the spraying agent tank

When handling the spraying agents, always

follow the safety instructions of these

operating instructions (pay special attention to

section 1.3) and the information provided by the

manufacturer of the particular spraying agent.

Before opening the spraying agent tank,

depressurise the device by pulling on the pressure

relief valve (Fig. 3).

Before pulling on the pressure relief valve (4), the

device must always be in an upright position.

Attention: Keep the device away from your face!

Spraying agent volume:

Mix the spraying agents according to the

instructions provided by the manufacturer of the

spraying agent. Choose the appropriate volume

according to requirements.

Mixing spraying agents:

Only mix spraying agents out in the open. Never do

this inside living spaces, stables or in storage

spaces that are used for food or animal feed.

Never mix the spraying agent directly in the

spraying agent tank.

Spraying agents in powder form:

x Mix the spraying agent in a separate container,

not in the spraying agent tank.

x Ensure that the mixture is thoroughly mixed

before pouring it into the spraying agent tank.

x Use the spray tube to thoroughly mix the

spraying agent in the tank.

Liquid spraying agents:

x Fill 1/4 of the spraying agent tank with clean

water.

x Then pre-mix the spraying agent with clean

water in a separate container according to the

instructions provided by the manufacturer of the

spraying agent.

x Pour the pre-mixed spraying agent into the

spraying agent tank.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Solo 462 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info