Bedienungsanleitung Solo 463 (Seite 24 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

655624

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

5 Maintenance, cleaning and storage

ENGLISH 10

If the delivery rate is still too low after cleaning the

nozzle and the filter element, or if the nozzle and/or

the filter element are worn or damaged, replace the

nozzle and/or the filter element by genuine SOLO

replacement parts.

Changing the spray nozzle and the filter element:

See section 5.3

5.3 Changing the spray nozzle and the

filter element

Only the spray nozzles listed in section 10 and the

genuine filter element (part no.: 40 74 922 25,

mesh aperture: 0.8 mm [0.031"]) must be used in

this pressure sprayer.

Spray nozzle and filter element must only be

changed if the device is depressurised.

Depressurise the device by pulling on the pressure

relief valve (Fig. 3).

Before pulling on the pressure relief valve (4), the

device must always be in an upright position.

Attention: Keep the device away from your face!

Changing the spray nozzle or the filter element:

x Rinse the nozzle attachment with clean water.

x Disassemble the nozzle attachment (Fig. 2).

x Clean the O-rings, the filter element and the

spray nozzle with clean water and a soft brush.

Never use your mouth to blow through the spray

nozzle! Never use hard objects to clean the

nozzles!

x Replace the previous nozzle by the new nozzle

or the previous filter element by the new filter

element.

x Reassemble the components of the nozzle

attachment (Fig. 2).

5.4 Greasing the sealing rings

If the pump or the pressure relief valve (4) is hard

to operate, the respective sealing rings are to be

greased with silicone grease or replaced if

necessary.

Clean/grease/replace the sealing ring of the

pressure relief valve:

x Place the empty and depressurized device

securely on level ground.

x Unscrew the pressure relief valve (4)

couterclockwise.

x The sealing ring of the pressure relief valve can

now be cleaned, greased or replaced by a new

one if damaged.

Part no. of the sealing ring: 00 62 116

x Put the pressure relief valve straight to the

connector and fasten it hand-tight by turning

clockwise. Do not use any tools!

Clean/grease/replace the sealing rings of the

pump:

x Place the empty and depressurized device

securely on level ground.

x Unscrew the pump couterclockwise from the

spraying agent tank (Fig. 5).

x The sealing ring on the upper pump end

(Fig. 6.3) can now be cleaned, greased or

replaced by a new one if damaged.

Part no. of the sealing ring: 00 62 341

x Pull-out the pump piston (Fig. 6.1) completely

and unscrew it counter-clockwise out of the

pump cylinder (Fig. 6.5).

Do not use force, and do not use any tools!

x The sealing ring on the pump piston (Fig. 6.4)

can now be cleaned, greased or replaced by a

new one if damaged.

Part no. of the sealing ring: 00 62 135

x Push the pump piston back into the pump

cylinder. Insert the piston socket (Fig. 6.2) into

the pump cylinder and hold it tight.

x Hold the piston socket and carefully pull out

again the pump piston completely.

x Turn the piston clockwise until the piston socket

clicks into place in the pump cylinder.

Do not use force, and do not use any tools!

5.5 Draining the spraying agent tank and

cleaning the spraying agent carrying

parts

Before opening the spraying agent tank and before

disassembling the nozzle attachment, depressurise

the device by pulling on the pressure relief valve

(Fig. 3).

Before pulling on the pressure relief valve (4), the

device must always be in an upright position.

Attention: Keep the device away from your face!

Drain the spraying agent tank and all other

spraying agent carrying parts daily after use and

particularly at the end of the spraying season and

thoroughly flush them with clean water.

Any unused spraying agent that is left over in the

device could cause corrosion and hence damage

the device. Special attention must be paid to

wearing parts like spray nozzles, filters and seals.

Please read and observe the cleaning instructions

supplied with the spraying agent.

Recommendation: Use the special SOLO cleaner

for plant protection sprayers (dosing bottle of

500 ml [approx. 16.9 oz], part no.: 49 00 600).

Never use aggressive, acid- or solvent-containing

cleaning agents (gasoline for example).

After cleaning, leave the spraying agent tank open

to dry.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Solo 463 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info