658836
37
Zoom out
Zoom in
Vorherige Seite
1/46
Nächste Seite
Operating and maintenance information - Maintenance of the chain brake, - Vibration damping,
- Spark plug information; - Replacing the fuel filter .
ENGLISH 37
E
N
G
8.4 Maintenance of the chain brake
Check for ease of movement and correct operation on a daily basis.
Remove any resin, sawdust and dirt
.
Grease should be applied to all visible joints and
bearings approximately once a week (indicated with
arrows in the diagram)
For improved access ! activate the chain brake
Chain brake function test (chapter 3.9).
8.5 Vibration damping
If you find that vibrations on the handles worsen significantly with time in comparison to when the
chainsaw was new, check the damping elements (rubber-bonded metal mountings) for damage and
replace them as required.
Working with the chainsaw while the vibration damping system is not working properly can
cause health problems.
8.6 Spark plug information
The spark plug should be regularly checked every 50 operating hours.
Take off the cowl from the chainsaw. (chapter. 3.4)
Disconnect the spark plug connector which is located underneath.
Unscrew the spark plug and dry it thoroughly.
In the event of severe burn-off of the electrodes the spark plug should be replaced immediately,
otherwise every 100 hours.
The engine must not be moved if the spark plug is removed or the ignition cable is
disconnected. Otherwise there is a risk that sparks could form which might cause a fire.
Interference-suppressed replacement spark plugs (calorific value: 200) are
available for example under the following trade names:
BOSCH WSR6F, CHAMPION RCJ-6Y or equivalent.
The prescribed electrode gap is 0.5 mm.
Before starting work, check the ignition cable to make sure the connections are in good working order
and the insulation is intact.
Screw the spark plug back in again.
Always press the spark plug connector firmly onto the spark plug.
Refit the cowl to the chainsaw.
8.7 Replacing the fuel filter
We recommend having the fuel filter changed annually by a specialised service centre.
A trained mechanic can carefully remove the fuel filter via a wire loop through the fuel tank filler.
Ensure that the thicker part of the fuel hose on the tank wall is not drawn into the fuel tank.
37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Solo 644 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info