Bedienungsanleitung Solo Port 423 (Seite 29 von 62) (Deutsch, Englisch, Französisch, Spanisch)

655794

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

Operation hints

ENGLISH 13

Nozzle attachment (6):

The nozzle attachment (6) is positioned onto the

standard nozzle (4) with the selected grille.

Use the dual grille (6a) when spraying cultures in

rows (e.g. vines, tomatoes, nurseries), to achieve

a good covering on the underside of the leaves.

The deflector grille can be replaced with a dual

grille (6b). The dual grille provides a 90° - 110°

spray pattern. The dual grille is usually used for

spraying two rows at a time. The deflector grille

and the dual grille can be placed onto the external

diameter of the nozzle, until the bead engages.

Dual nozzle (accessories, part no.: 49 00 137):

Remove standard nozzle (4) from the spray wand

and push the dual nozzle onto the spray wand.

11.2 Residual spray medium

Switch off the appliance as soon as no further

liquid is expelled, when the metering body is

correctly positioned for spraying, or air bubbles are

visible inside the lance supply hose.

The tank will then contain less than 100 ml

residual medium.

If you don’t want to refill the tank with spray

medium and you want to terminate spraying, dilute

the residual medium with 2 l of water. Dispose of

this solution on the treated area.

11.3 Strainer for accessory sets

When using the liquid pump (accessory part no.:

44 00 117) or the ULV accessory (part no.: 49 00

479), a strainer is integrated into the tank

connector.

The strainer has a mesh size of 0.32 mm. Only use

original strainer part no.: 25 00 198 with standard

mesh size when replacing the strainer.

11.4 Checking the spray medium flow rate

At the beginning of the spraying season, check

whether the equipment flow rate (l/min) still

corresponds to the „Guide values“ table.

For this, fill the equipment up to the maximum

marker with water, start using the equipment and

spray for one minute exactly at maximum operating

pressure. Then measure the water volume required

to bring the water level back up to the maximum

marker.

The actual volume measured represents the flow

rate of the equipment in l/min at maximum

operating pressure.

It should not deviate by more than 10 % from those

listed in the “Guide values” table. Should the actual

value be too low, sediments inside the metering

body may be the cause. Clean the corresponding

parts and repeat the checking procedure.

Should the actual value be too high, the metering

body may be worn or damaged. In that case,

replace the metering body with a new one (part

no.: 40 74 165).

When using accessory sets (liquid pump part no.:

44 00 117 or ULV accessory, part no.: 49 00 479) a

strainer will be integrated into the tank connector.

In that case, an incorrect flow rate can also be due

to a contaminated or worn strainer.

Clean or replace the contaminated/worn strainer

(part no.: 25 00 198).

Fig. 12

Fig. 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Solo Port 423 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Solo Port 423

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info