Bedienungsanleitung Sommer Marathon 550SL (Seite 15 von 32) (Englisch)

474214

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Initial operation

Check door end positions

for OPEN + CLOSED

The running path of the drive can be extended or shortened by means

of the guide idlers.

Check whether the door opens and closes completely. If this isn't the case,

then the running path must be adjusted.

1. Actuate control device (e.g. button, hand-held transmitter, etc.) once.

 The door opens to the until the door OPEN end position is reached.

2. Check whether the door reaches the desired end positions.

 Adjust the end positions if necessary. See the chapter

“Commissioning – adjusting the door Closed + Open end positions”.

Checking the emergency release

NOTE!

You can activate Backjump for sectional doors or doors

with ceiling guides by means of DIP switch 6; this relieves

the drive and door mechanisms. Simpler actuation of the

emergency release.

1. Close the door with the drive.

2. Pull once on the emergency release (N).

If the emergency release cannot be actuated, loosen the end switch (V)

and push it a bit in direction (1).

3. Open and close the door with the drive. Recheck the emergency release.

Check the force settings

For every run of the door, the controller compares the stored force values

with the actual values required and automatically adjusts the stored values

upon reaching the end position.

Check: See chapter “Care and maintenance/regular testing”.

Programming the hand-held

remote control

NOTE!

Before programming the hand-held transmitter for the ﬁ rst

time, always clear the radio receiver memory completely.

3.1

3.2

3.1

3.2

Deleting the radio receiver memory

1. Press and hold the Learn button (1).

 After 5 seconds, the LED ﬂ ashes (3.1 or 3.2).

 After another 10 seconds, the LED lights up steadily (3.1 or 3.2).

 After a total of 25 seconds, all LEDs light up steadily (3.1 and 3.2).

2. Release the Learn button (1) – the deletion procedure is ended.

Programming the hand-held remote control

1. Press the Learn button (1).

▫ 1x for channel 1; the LED (3.1) lights up.

▫ 2x for channel 2; the LED (3.2) lights up.

 If no code is sent within 10 seconds, the radio receiver switches to

Normal mode.

2. Press the desired hand-held transmitter button (5) until the LED (3.1/3.2)

extinguishes, depending upon which channel has been selected.

 LED extinguishes – programming is ﬁ nished.

 The hand-held transmitter has transferred the radio code to the

radio transmitter.

3. For the additional programming of hand-held transmitters, repeat the

steps above. A maximum of 112 memory locations are available for

each radio receiver.

Interrupting the Learn mode:

Press the Learn button (1) until no more LEDs are lit.

Mount the information sign

BACK

HINTEN

BACK

HINTEN

-1

-0-OC

v.A

1x1

-17

-0-O

The information sign concerning the function of the emergency release;

please hang on the emergency release cord.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sommer Marathon 550SL Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sommer Marathon 550SL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info