Bedienungsanleitung Sommer S 9060 base plus (Seite 45 von 80) (Englisch)

680552

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

46900V001_Rev-D_EN

10. Connections and special functions of the motor

carriage

10.15 Setting automatic closing function -

defining basic values

When automatic closing is activated, the door is opened

by a pulse.

The door moves to the door OPEN end position.

The door closes automatically after the hold open time.

With the factory settings, the door also closes

automatically from the partial opening position when

the automatic closing function is activated.

WARNING

Risk of injury during automatic

closing!

Automatically closing doors can injure

people and animals in the movement

area of the door when the door is

closing. This may cause serious or fatal

injury.

► Always keep the moving door in sight.

► Keep persons and animals clear of the

range of movement of the door.

► Never put your hand near the door

when it is moving or near moving parts.

In particular, do not reach into the

ceiling holder or the push arm.

► Do not drive through the door until it has

opened completely.

NOTE

If the door is not in view and the operator is

actuated, objects in the movement area of

the door may be jammed and damaged.

Objects must not be in the range of

movement of the door.

INFORMATION

The door opens completely if it hits an

obstacle.

INFORMATION

Operation with automatic closing must

comply with EN 12453. This is a legal

requirement. National regulations must be

observed in non-European countries.

A photocell must be connected. Bridging

the safety inputs with wire bridges is not

permitted.

1. Close the door.

2. Set DIP switch 1 to ON.

3. The hold open time of the door is 30 seconds.

Every new command within 30 seconds restarts

the hold open time. If button 1 on the transmitter is

pressed, the door moves to door OPEN end position.

The door movement cannot be stopped with the

transmitter.

4. The door closes automatically after 30 seconds.

The closing movement can be stopped by a

command with the transmitter.

⇒ Door opens completely - after reversal of direction.

5. The door starts the closing process again after

30 seconds.

⇒ Door CLOSE.

INFORMATION

The factory setting is fully automatic

closing with a preset hold open time of

30 seconds from the door OPEN end

position and 60 seconds from partial

opening.

When driving through, the photocell

is activated and the hold open time is

shortened to 5 seconds for sectional doors

and side-opening sectional doors.

This setting and the selection of semi-

automatic closing can be set via SOMlink

and a WiFi-enabled device.

INFORMATION

The pre-warning time can be activated and

adjusted via SOMlink and a WiFi-enabled

device.

The progress of the pre-warning time is

displayed by the ashing operator lighting

and the warning light.

10.16 Setting the lighting function

The operator lighting on the motor carriage can be

switched on and off separately via radio channel CH 2.

This function is pre-set in the factory settings.

Program the desired handheld transmitter button on radio

channel CH 2.

The factory setting of DIP switch 2 is OFF, and the

lighting function is therefore activated.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sommer S 9060 base plus Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sommer S 9060 base plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info