Bedienungsanleitung Sommer S 9060 base (Seite 71 von 80) (Englisch)

680551

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

46900V001_Rev-D_EN

16.3 Time sequences of operator lighting in normal mode and in case of faults

The flash sequences show information on malfunctions for technicians, end customers and telephone support.

In normal mode

Flash sequences Possible cause Corrective action

Operator lighting blinks as warning light

• Programming mode activated

• Pre-warning time activated

• Reversing movement, soft reversing

and stopped after a soft and

reversing movement

• Function for HFL activated

• None, for information

In the event of errors

Flash sequences Possible cause Corrective action

Requirement

Operator expects a command

• Waiting for a conformation during the

position programming movement of

door CLOSE end position

• Conrmationofpositionprogramming

movement

Alarm

A process has triggered a fault

• Photocell or safety device not OK

before movement

• Check photocell, realign if necessary

• If necessary, have components

replacedbyaqualiedspecialist

• Interruption of a safety device during

the movement

• Remove obstacle

• Dead man movement, safety device

not OK

• Haveitcheckedbyaqualied

specialist

• Motor return from outside (e.g. due

to attempted break-in)

• For information

Service

A process has triggered a fault

• Service required (service days,

service cycles have been reached)

• Have the service performed by a

qualiedspecialist

• It may be that after 180 days, the

basic force curve data for the door

operation vary from the actual data

• Check weight-balancing and door

mechanism

• If necessary, carry out force reset,

see Chapter "10.13 Resetting the

control unit", section "Deleting the

force values"

• Motor temperature is too high

(overheating)

• Allow motor to cool

• Programmingofdifcultpositions

in case of reversing with no visible

cause. The complete distance is

traversed from end position to end

position (dead man by radio, under

direct view only)

• For information

Fault

Operator or parts of the operator faulty

• Self-test of electronics

• Blockage detection (gear breakage,

Hall sensor fault)

• Have it checked and, if necessary,

componentsreplacedbyaqualied

specialist

• Limit switch does not operate

(e.g. wire break, limit switch fault)

• Have cable connections checked

byaqualiedspecialistand,

if necessary, have components

replaced

• Counting pulses sent in the wrong

direction (motor cable was incorrectly

connected)

• Check wiring, correct if necessary

• Run time exceeded • Path too long, path restricted to max.

7,500 mm

• Error during plausibility test of Memo • Haveitcheckedbyaqualied

specialist and, if necessary, have

components replaced

16. Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sommer S 9060 base Seite 71

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sommer S 9060 base

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info