Bedienungsanleitung Sommer S 9060 Tiga (Seite 75 von 96) (Englisch)

680825

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

S10564-00001_Rev-A_EN

13. Operation

Fig. 7

7. After the door CLOSE end position has been reached,

the traffic lights on both sides are switched off.

⇒ Both sides: Trafc lights off.

13.4 Obstacle detection

The operator stops and reverses slightly if it encounters

an obstacle. This prevent injury and damage to property.

The door will be partially of completely opened depending

on the setting. The partial reversal is pre-set at the

factory. A full reversal can be set with SOMlink and a

WLAN-enabled device.

INFORMATION

In the automatic closing function the door

opens completely.

INFORMATION

If the photo eye is interrupted, the door

runs on for a long distance.

The following safety devices are installed to detect

obstacles:

• Photo eye (object protection)

• Safety contact strips (personal protection)

• Force cut-off of operator (personal protection)

For more, also note Chapter "14. Maintenance and care".

Force cut-off in door OPEN direction

⇒ If the door meets an obstacle, the door stops,

reverses a bit in the door CLOSE direction and

stops.

⇒ Operator expects a new command and does not

start automatically.

⇒ After receiving a command, the operator moves in

the door OPEN direction.

Force cut-off in door CLOSE direction with automatic

closing function

⇒ If the door meets an obstacle, the door stops and

reverses a bit until it reaches the door CLOSE end

position.

⇒ The door closes automatically after the open

holding time.

INFORMATION

If the door encounters an obstacle again

in the door CLOSE direction, the operator

stops and reverses completely to the door

OPEN end position. The door stays there.

The automatic closing function is

interrupted. The open holding time and

clearing time do not start again until a

command for door CLOSE.

The door is then automatically closed.

Safety

If the SAFETY safety input is open, the operator stops

the door movement. No more commands are executed.

The potential-neutral NC contact, for example, is suitable

for connecting an emergency stop.

⇒ Status LED on the control unit ashes.

Resetting the SAFETY safety input:

1. Reset safety input

(close contact).

2. Execute a command using the button.

⇒ Door opens up to door OPEN end position.

⇒ Open holding and clearing time run out.

⇒ Door closes automatically.

13.5 Power-saving mode

To save energy, the operator control unit switches to

power-saving mode after the factory-specified period.

Connected accessories are deactivated and then

reactivated at the next command from a button or radio.

Connected accessories may include: photo eye, safety

contact strip and external radio receiver.

Because external radio receivers are deactivated in

power-saving mode, they cannot receive commands from

the remote control and send them to the operator.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sommer S 9060 Tiga Seite 75

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sommer S 9060 Tiga

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info