680782
63
Zoom out
Zoom in
Vorherige Seite
1/88
Nächste Seite
63
S10931-00001_Rev-D_EN
12. twin operation
12.1 twin operation
Two operators can be controlled with one control unit,
for example in a double garage with two garage doors.
Both operators are connected to one control unit for this
purpose.
2
1
Fig. Installation example for twin operation, slave (1) and
master (2)
Mode of operation
If one of the operators receives a command and
starts to move, the other operator is locked for this
time. The other operator can only be started after the
movement has stopped.
INFORMATION
Both operators cannot be operated at the
same time.
12.2 Installing the operators
The installation of the operators is described here using
an example.
1. Install the operators on the two doors as described in
the Chapter "6. Installation."
12.3 Selecting and configuring master
and slave
Requirements
Both operators are configured as a master in the factory
settings. The main communication with the control unit
is effected via the master.
INFORMATION
No automatic closing function and no
energy-saving mode are possible in twin
operation.
1. Set DIP switches 1 and 3 on the wall control unit to
"ON." This sets membrane keypad T1 for the master
and membrane keypad T2 for the slave.
T1
T2
Fig. Membrane keypad T1 and T2 of wall control unit
T1 for master
T2 for slave
GND
+24V
gn
rt
+
-
Fig. Connection of chain and track for both operators to the
control unit
Terminal block Function
gn + Track
rd - Chain
2. Connect the operator (1) to the terminal blocks for
chain (rd) and track (gn) of the wall control unit.
The connection cable must be firmly secured to
prevent displacement.
3. Connect the wall control unit to the mains voltage.
Check that the power supply is connected.
4. Configure the operator (1) as the slave. To do this,
establish a connection to the motor carriage via
SOMlink and a WiFi-enabled device.
5. In the menu, under the "twin operation" settings,
configure "Operator is slave" for the selected
operator and save the entry. Check the entry.
6. Disconnect the wall control unit from the mains
voltage.
7. Connect operator (2), the master, to the wall control
unit in parallel to the terminal block for chain and
track. The connection cable must be firmly secured
to prevent displacement.
8. Reconnect the control unit to the mains voltage.
63

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sommer S 9080 pro wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Sommer S 9080 pro

Sommer S 9080 pro Bedienungsanleitung - Deutsch - 88 seiten

Sommer S 9080 pro Bedienungsanleitung - Holländisch - 88 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info