Bedienungsanleitung Sommer S 9080 Tiga (Seite 84 von 96) (Englisch)

680826

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

S10564-00001_Rev-A_EN

15. Troubleshooting

15.4 Troubleshooting table

Problem Possible causes Test/check Remedy

The operator opens

the door when the

transmitter or control

device is actuated but

does not close it.

• Photo eye and safety

device have been

destroyed

• Check photo eye and safety

devices

• Remove obstacle

• The photo eye must be aligned

• If necessary, have it checked and

replaced by a qualied specialist

• Automatic closing

function activated

• Wait to see whether the operator

starts automatically after

30 seconds

• Automatic closing function

deactivated

• Have the cause corrected by a

trained electrician

Operator cannot be

operated with the

control device.

• No power • Check power supply • Check the power socket with a

different device, for example with a

lamp

• End switch in carriage

defective

• Unlock operator and push

carriage to the centre of the

track

• Lock operator

• Actuate transmitter

• If the operator still does not

close and open, the end switch

is defective

• Have the end switch replaced by a

qualied specialist.

• The operator was

unlocked by the

emergency release

mechanism

• Check that the door can be

moved manually

• Pull the emergency release to

activate the operator, see Chapter

"13.7 Function of the emergency

release"

• Control device incorrectly

connected to the operator

• Check function of operator with

a transmitter

• Check wiring, correct if necessary

• Transmitter defective • Operator cannot be started with

the transmitter

• Check transmitter power supply

• If necessary, replace the battery of

the transmitter

• If necessary, replace the transmitter

with a new one

• Operator defective • Operator cannot be started with

the transmitter or the connected

control device

• Have operator repaired or replaced

by a qualied specialist

• Electrical supply voltage

outside the approved

range

• Have the mains voltage checked

by a trained electrician

• Have the cause corrected by a

trained electrician

• SAFETY safety input,

e.g. emergency stop,

triggered

• Status LED is off, the status

LED flashes

• Reset SAFTEY safety input, see

Chapter "11.9 Safety terminal"

When a button on the

transmitter is pressed,

the door does not

open or close.

• Transmitter not

programmed

• Radio LED does not light when

the transmitter is operated

• Program transmitter

• Battery in the transmitter

is at

• Replace the battery of the

transmitter

• Transmitter defective • LED on transmitter does not

light

• Replace transmitter

Radio command

cannot be

programmed

• Memory full • All four LEDs blink cyclically for

about 3 seconds

• Memory full, see Chapter

"10.5 Programming the

transmitter"

MEMO Identier error • Incorrect MEMO • All four LEDs blink cyclically for

a short time and then go out for

a long time.

The operator lighting of the

carriage blinks 4 times short and

4 times long.

• Disconnect operator from the power

supply, unplug Memo,

re-supply operator with power

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sommer S 9080 Tiga Seite 84

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sommer S 9080 Tiga

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info