680556
51
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
51
46900V001_Rev-D_EN
11. Connections and special functions of the ceiling
control unit
11.3 Setting the DIP switches on the
ceiling control unit
Special functions can be set with the DIP switches on the
ceiling control unit.
All DIP switches are set to OFF by default.
NOTE
Do not use a metal object to set the
DIP switches, because this may damage
the DIP switches or the circuit board.
Use a suitable tool to set the DIP switches,
such as a at, thin plastic object.
DIP switches
on the ceiling
control unit ON
OFF
1
ON
1
23
4
"Conex"
additional
circuit board
T1denes
door OPEN
T2denes
door CLOSE
"Conex"
additional
circuit board
T1 pulse
sequence
T2 lighting
function/partial
opening
2
ON
1234
Relay
(MUFU) trips
during door
movement
and if the door
is not closed*
Relay (MUFU)
lighting
function
3
ON
1234
Continuous
power to the
complete
system
activated
Power-
saving mode
activated
4
ON
1234
COM and
Signal
activated
as button
input (partial
opening)
COM and
Signal
activated as
safety contact
for photocell
* e.g.: door status display
11.4 Button 2 for partial opening
If required, another button can be connected for partial
opening operation. After installation of the keypad, all
settings must be made on the ceiling control unit and the
motor carriage.
NOTE
The control unit cover is connected to the
circuit board of the ceiling control unit via
a connection cable. If an accumulator has
been installed, it is also connected to the
circuit board.
Carefully remove the control unit cover
and disconnect the connections to prevent
damage to the ceiling control unit.
INFORMATION
If button 2 (partial opening) is used,
a photocell cannot be connected.
The automatic closing operating mode is
then not possible.
Installing the keypad
1. When installing the potential-free keypad, select a
suitable position at a height of at least 1.6 m.
2. Install the keypad.
3. The keyboard cable for the ceiling control unit must
be firmly secured to prevent displacement.
Installation of the control cable and settings on the
ceiling control unit
1. Disconnect the operator from the mains voltage.
Check that the operator is disconnected from the
power supply.
2. Unscrew the cover from the ceiling control unit.
3. If an accumulator is used, it must also be
disconnected, see Chapter "11.11 Installing and
removing the accumulator".
4. Remove the control unit cover.
WL
24V/1A
Signal
COM
GND
+24V
O
12
WL
2
4V
/
1
A
O
1
2
G
N
D
+24
V
ON
1234
Fig. 5 Fig. 6
51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sommer S 9110 base plus wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Sommer S 9110 base plus

Sommer S 9110 base plus Installationsanweisung - Deutsch - 80 seiten

Sommer S 9110 base plus Installationsanweisung - Holländisch - 80 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info