Bedienungsanleitung Sommer S 9110 base plus (Seite 58 von 80) (Englisch)

680556

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

46900V001_Rev-D_EN

12. twin operation

9. Programme the handheld transmitters for the

respective operators, see Chapter "10.4 Explanation

of the radio channels" and "10.5 Programming the

transmitter".

INFORMATION

Only one handheld transmitter can

be assigned per function. Undesired

malfunctions could otherwise occur.

12.4 Partial opening

One partial opening can be programmed for each of

the two operators (master and slave). Programming or

deletion is performed as for the standard equipment,

see Chapter "10.17 Setting partial opening" and

"10.18 Deleting partial opening".

Example:

Master on radio channel CH 2 (partial opening) on

handheld transmitter button 3. For the slave, on radio

channel CH 2 (partial opening) on handheld transmitter

button 4.

Wired

The COM input and signal on the ceiling control unit can

be used for this purpose. DIP switch 4 on the ceiling

control unit must be ON.

The input is then no longer available for connection of a

photocell.

Mode of operation

If button 2 (partial opening) is activated, the master

receives the partial opening command. See also chapter

"10.17 Setting partial opening".

12.5 Defined opening and closing

The functions Defined opening and closing of the

operators (master and slave) can only be configured via

the CH 3 and CH 4 radio channels. These settings are

not available when corded or via the Conex accessory

part.

12.6 Door status display

If DIP switch 2 on the ceiling control unit is set to ON,

the relay is activated during door movement and when

the door is open. It remains activated until both operators

(master and slave) are again at the door CLOSE end

position.

12.7 Lighting for twin operation

The lighting can be switched on and off for the selected

operator via the respective handheld transmitter. This

also applies for the connected supplemental lighting, see

also Chapter "10.16 Setting the lighting function".

12.8 Photocell

Optionally, a photocell can be connected. The photocell

must be configured in such a way that it can be aligned

to cover two doors. If the photocell is interrupted, the

operator of the moving door reverses. See also chapter

"11.6 Photocell and frame photocell".

INFORMATION

If a photocell is retrotted on a

programmed system, the control unit must

be reset, see Chapter "10.13 Resetting the

control unit."

12.9 External button

With the Conex additional circuit board, both operators

(master and slave) can be operated in pulse sequence

mode. Fit the Conex as described in the separate

instructions. Set DIP switch 1 on the ceiling control unit

to ON.

Mode of operation

Button 1 - master

Button 2 - slave

12.10 Reset

The slave becomes the master again when a factory

reset is carried out. The operator must be configured as

the slave again via SOMlink and a WiFi-enabled device,

see Chapter "12.3 Selecting and configuring master

and slave".

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sommer S 9110 base plus Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sommer S 9110 base plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info