680783
57
Zoom out
Zoom in
Vorherige Seite
1/88
Nächste Seite
57
S10931-00001_Rev-D_EN
11. Connections and special functions of the wall
control unit
11.3 Setting the DIP switches on the
wall control unit
Special functions can be set with the DIP switches on
the wall control unit. All DIP switches are set to "OFF"
in the factory settings.
NOTE
Do not use a metal object to set the DIP
switches, because this may damage the
DIP switches or the circuit board.
Use a suitable tool, for example a at
plastic object, to set the DIP switches.
DIP switch on
wall unit
OFF
ON
1
ON
1
23
4
Membrane
keypad T1 for
deneddoor
OPEN
Membrane
keypad T2
deneddoor
CLOSE
Membrane
keypad T1
for pulse
sequence
Membrane
keypad
T2 lighting
function/partial
opening
2
ON
1234
Relay
(MUFU) trips:
during door
movement and
if the door is
not closed*
Relay (MUFU)
lighting
function
3
ON
1234
Continuous
power to the
complete
system
activated
Power-saving
mode activated
4
ON
1234
COM and
Signal
activated
as button
input (partial
opening)
COM and
Signal
activated as
safety contact
for photocell
* e.g.: door status display
11.4 Button assignment of wall control
unit
T1
T2
Fig. Membrane keypad T1 and T2 of wall control unit
Factory settings of the functions of the
membrane keypads
Membrane keypad T1 – pulse sequence
Membrane keypad T2 – lighting function or partial
opening, dependent on DIP switch 2 on motor
carriage
Setting options
If DIP switch 1 is set to "ON" on the wall control unit:
MembranekeypadT1–denedOPEN
MembranekeypadT2–denedCLOSE
11.5 Button 2 for partial opening
If required, a further button can be connected to the
control unit for partial opening operation.
After installation of the keypad, all settings must be made
on the ceiling control unit and the motor carriage.
NOTE
The control unit cover is connected to the
circuit board of the wall control unit via
a connection cable. If an accumulator has
been installed, it is also connected to the
circuit board.
Carefully remove the control unit cover
and disconnect the connections to prevent
damage to the wall control unit.
INFORMATION
If button 2 (partial opening) is used,
a photocell cannot be connected.
The automatic closing operating mode
is then not possible.
57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sommer S 9110 pro wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Sommer S 9110 pro

Sommer S 9110 pro Bedienungsanleitung - Deutsch - 88 seiten

Sommer S 9110 pro Bedienungsanleitung - Holländisch - 88 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info