Bedienungsanleitung Sonic Alert HA360BU (Seite 1 von 2) (Englisch)

771661

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

HA360BU – SONICBRIDGE™ / LAMP SWITCH

The HomeAware™ SonicBridge™ module HA360BU

allows traditional Sonic Alert receivers to work with the

new HomeAware™ D-RF Secure™ system. The

HomeAware™ is the only wireless system available

that is compatible with all Sonic Alert remote receivers

including the SA101, SA201, BL300, RH100 and

SB1000 alarm clock. It also has the added feature of

allowing a lamp to be plugged into it to allow for a

flashing lamp option. To install the SonicBridge™

follow the four steps below.

1. Simply plug the SonicBridge™ into any 120v outlet

(do not plug into extension cords, power strips or

surge protectors) must be plugged directly into the

outlet for the best receiver reception.

2. Plug the opposite end into the back of the

HomeAware™ Main unit where it says Lamp SW.

3. You are now connected to the home power line

which will allow the HomeAware™ to communicate

with your traditional Sonic Alert remote receivers.

4. If you would like to utilize the option of a flashing

lamp for your alerts simply plug any lamp into the

SonicBridge™ and turn the lamp switch to the on

position. Your lamp can now be turned on and off

through the HomeAware™ Main unit by pressing

the snooze button for on and off.

Important notes for lamp bulb type

Lamp light bulb must not exceed 300 watts. Also make

sure the lamp is in the on position and that the bulb is a

good bulb.

Bulb types to use in lamps are as follows;

Incandescent, LED, and instant on CFL type bulbs

must be used.

FCC Requirements

This device complies with part 15 of the FCC rules, and

with RSS-210 of Industry Canada. Operation is subject

to the following two conditions; (1) This device might

not cause harmful interference, and (2) this device

must accept any interference received, including

interference that may cause undesired operation.

Note: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC rules. These limits are

designed to provide responsible protect against harmful

interference in a residential installation. This

equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions manual, may cause

harmful interference to radio communications.

However, there is no guarantee that interference will

not interfere in a particular installation. If this equipment

does cause harmful interference to radio or television

reception, which can be determined by turning the

equipment on and off, the user is encouraged to thy to

correct the interference by one or more of the following

measures:

i. Reorient or relocate the receiving antenna.

ii. Increase the separation between the

equipment and receiver.

iii. Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

iv. Consult the dealer or and experienced radio/

TV technician for help

Modification not expressly approved by the

manufacturer could void the user’s authority to operate

the equipment under FCC rules

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sonic Alert HA360BU Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info