Bedienungsanleitung Sonic Alert HA360SSBC (Seite 1 von 2) (Englisch)

771667

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

INSTALLATION AND SET UP FOR HOMEAWARE™ TRANSMITTER

HA360SSBC – Baby Cry

The HomeAware™ HA360SSBC transmitter is

designed to alert you to the sound of a baby crying.

This transmitter alerts you through the HomeAware™

Main unit and remote receivers located in other rooms.

Battery Backup Installation

Install a new 9 volt alkaline battery into the battery

compartment located on the back of the unit. See

diagram for battery door location. Battery backup will

provide power when a power outage has occurred.

Power will be provided for a continuous outage lasting

7 days, or for short outages up to two years.

Link Button Set Up

This procedure will link the HA360SSBC – Baby Cry to

your Main unit. The Main unit will also provide an alert

to all HomeAware™ remote receivers. When using the

Bridge unit HA360BU all original Sonic Alert receivers

(SA101, SA201, BL300, and SB1000) will also alert

you.

It is best to do the link procedure in the same room with

the HomeAware™ Main unit, make sure the unit is

plugged in.

To link a transmitter to your HomeAware™ Main

unit:

1. Press set up button and the word LINK will be

shown on the display, press Enter. LINK will begin

blinking. (If LINK mode is entered by accident,

simply press the BACK button to exit and return to

the clock.)

2. Press and hold down the Link button on the back of

your transmitter for about 1 second. The red LED

on the transmitter will light up. Release the button.

3. Upon successful connection, the red LED on the

transmitter will flash 2 times, then turn off. The

HomeAware™ main unit will briefly show DONE,

and return to the time display. Your transmitter is

now connected and ready to test and use.

Sensitivity Switch

You can adjust the sensitivity of the Baby Cry detector.

There are three levels to choose from: The HI setting is

the most sensitive setting and will alert you to more

sounds. Moving this switch to MED makes it less

sensitive and will alert you to less sound. The LO

setting is the least sensitive. If you are not picking up

the sound you need to be alerted to, simply move the

sensitivity switch to a higher setting. If you have set this

setting to HI and you are still not picking up the sound

try moving the transmitter closer to the sound.

When a sound is detected it will send a signal to the

HomeAware™ base unit and all HomeAware™ remote

receivers, also the red LED light will flash on the front

of the unit.

Low Voltage Input

HomeAware™ transmitters have a low 120 volt AC

power supply that powers the HA360ss. Simply plug

the unit into any 120 volt AC power outlet. Next plug

the other end into the Low Voltage Input located on the

side, see diagram below.

FCC Requirements

This device complies with part 15 of the FCC rules.

Operation is subject to the following two conditions; (1)

This device might not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesired

operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sonic Alert HA360SSBC Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info