Bedienungsanleitung Sonnenkonig MERKUR (Seite 47 von 55) (Deutsch, Englisch, Französisch, Italienisch)

703437

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

46 47

3. Installation

A mounting bracket is provided with the heater. The

bracket has been speciﬁcally designed to allow the prod-

uct to be ﬁtted to a ceiling. Before drilling the holes for

the ceiling mount, please ensure that the surface is solid

and that there are no hidden water pipes or electrical

wires. The heater must be installed no less than 50 cm

from any side walls and no less than 2.4 m from the ﬂoor.

Warning: The appliance must be installed on solid sur-

faces such as concrete, wood or metal, etc.

Important: Please ensure that the supply cable is well secured so that it does not come into

contact with the reﬂector or trail into the heated area. The supply cable can be ﬁxed to the

metal mounting bracket behind the heater with plastic zip ties.

1. This heater should be installed by a competent person, i.e. a qualiﬁed electrician.

2. Always disconnect the heater from the electrical supply and allow it to cool before installation.

3. When mounting on a ceiling, the lowest part of the heater must be located at or above a

minimum height of 2.4 m from ground level so that the heater cannot be touched when in

operation.

4. When mounting on a ceiling, there must be a distance of 2.4 m between your appliance and the ﬂoor.

5. When mounting on a ceiling, there must be a distance of 0.5 m between any side walls and

the appliance.

6. There must be a minimum distance of 1 m between your appliance and any living beings.

7. There must be a distance of at least 1 m between the front side of the heater and materials

such as wood, cardboard or cloth, etc.

8. When mounting on a ceiling, do not position the heater at an angle more than 90° or less

than 45°.

9. The supply cable must be at the lower end of the heater if the heater is installed at an angle

or vertically.

10. Keep the supply cord away from the body of the heater, which will get hot during use.

11. Do not install the heater on an inﬂammable surface.

12. Observe the minimum safe distance between the heater body and the inﬂammable surfaces

when mounted.

13. The heater should always have a minimum clearance of 0.5 m from the ceiling and adjacent walls.

14. If the heater is to be used outside, a weatherproof outlet is recommended.

15. Before drilling, ensure that there are no wires or water pipes in the area where the heater is

to be installed.

16. The heater must be installed on the mounting brackets provided.

17. Fasten the brackets securely to the mounting surface and to the back of the heater using the

ﬁttings supplied.

18. Fasten the heater securely onto the brackets using the ﬁttings supplied.

19. The brackets can be used to adjust the direction of the heater. Adjust the heater angle by

loosening the two bolts on the ceiling-mounting bracket and tighten the bolts again when

the desired angle is reached.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sonnenkonig MERKUR Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info