Bedienungsanleitung Sonos zp120 (Seite 21 von 144) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

160317

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

Sonos ZonePlayer 120 Setup Guide

When adding the handheld Sonos Controller, it fails to detect the

ZonePlayer(s)

Wireless interference or a network problem may be preventing the Controller from joining your

Sonos Multi-Room Music System.

1. Verify that this is not a DHCP or network problem.

• Disconnect the Ethernet cable from the back of the ZonePlayer so that it is not connected

to your network.

• Unplug the ZonePlayer's power cord and then plug it back in.

• When the status indicator light on the front of the ZonePlayer stops blinking white, try

adding your Controller again.

If it works, your router's DHCP server may have run out of available IP addresses to assign to the

Controller. In most cases you can log into your router by typing http://192.168.1.1 into your

browser’s address line (the IP address of your router may be different). Check the DHCP settings

and increase the number of IP addresses available in the DHCP scope.

If your Controller still does not recognize the ZonePlayer after completing this step, you can try

step 2 below.

2. Turn off any 2.4GHz cordless phones.

Some 2.4GHz cordless telephones can cause wireless interference. If turning off your 2.4GHz

cordless phone resolves the problem, you should consider switching to a 5.8Ghz or 900Mhz

phone (or change the wireless channel your Sonos system is operating on - see step 4 below.)

3. Put 108 Mbps wireless routers into 54 Mbps mode.

Sonos cannot function properly when a router is operating in turbo mode. In order to double the

speed from 54 Mbps to 108 Mbps, the router goes into a wide bandwidth mode which utilizes

most of the 2.4 GHz spectrum that the FCC has set aside for 802.11b/g devices. This means that

interference (RF noise) will occur with any other 2.4 GHz device that is not operating on the same

channel as the 108 Mbps device (usually channel 6). While it is possible to put all of your wireless

devices on channel 6, it is unwise. The devices will have to compete for available bandwidth, and

your entire wireless network will become sluggish and bogged down.

4. Change the wireless channel your Sonos system is operating on.

• Using the Desktop Controller for Windows: From the File menu, select Preferences. Click

the Advanced tab, and select another wireless channel from the Wireless Channel list.

• Using the Desktop Controller for Macintosh: From the Sonos menu, select Preferences.

Click the Advanced tab, and select another wireless channel from the Wireless Channel

list.

It may take several seconds for the switch to take effect. If you have music playing, a short music

dropout will occur during the wireless channel change.

Downloaded from www.Manualslib.com manuals search engine

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sonos zp120 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sonos zp120

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info