Bedienungsanleitung Sony bravia kdl-46x3500 (Seite 7 von 52) (Englisch)

141498

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Start-up Guide

3 Press F/f/G/g to select the language

displayed on the menu screens, then press

4 Press F/f to select the country/region in

which you will operate the TV, then press

If the country/region which you want to use on the

TV does not appear in the list, select “–” instead

of a country/region.

5 Before you start auto tuning the TV, insert

a pre-recorded tape into the VCR

connected to the TV (page 5) and start play

back.

The video channel will be located and stored on

the TV during auto tuning.

If no VCR is connected to the TV, skip this step.

6 Press G/g to select “OK”, then press .

7 Press F/f to select “Antenna” or “Cable”,

then press .

If you select “Cable”, the screen for selecting the

scan type appears. See “To tune the TV for digital

cable connection” on page 7.

The TV starts searching for all available digital

channels, followed by all available analogue

channels. This may take some time, so do not

press any buttons on the TV or remote while

proceeding.

If a message appears for you to confirm the aerial

connection

No digital or analogue channels were found.

Check all the aerial connections and press to

start auto tuning again.

8 When the Programme Sorting menu

appears on the screen, follow the steps of

“Programme Sorting” on page 40.

If you do not wish to change the order in which the

analogue channels are stored on the TV, go to next

step.

9 Press MENU to exit.

The TV has now tuned in all the available

channels.

When a digital broadcast channel cannot be received, or

when selecting a country/region in which there are no digital

broadcasts in step 4 (page 7), the time must be set after

performing step 9.

To tune the TV for digital cable connection

1 Press F/f to select “Scan Type”, then

press .

2 Press F/f to select “Quick Scan” or “Full

Scan”, then press .

“Quick Scan”: Channels are tuned according to

the cable provider’s information within the

broadcast signal. The recommended setting for

“Frequency”, “Network ID” and “Symbol Rate” is

“Auto” unless your cable provider has supplied

actual values to use. “Quick Scan” is

recommended for fast tuning when this is

supported by your cable provider.

“Full Scan”: All available channels are tuned and

stored. This procedure may take some time. This

option is recommended when “Quick Scan” is not

supported by your cable provider.

For further information about supported cable

providers, refer to the support web site:

http://support.sony-europe.com/TV/DVBC/

3 Press G/g/f to select “Start”, then press

The TV starts searching for channels. Do not press

any buttons on the TV or remote.

Some cable providers do not support “Quick Scan”. If no

channels are detected using “Quick Scan”, perform “Full

Scan”.

Auto tuning the TV

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony bravia kdl-46x3500 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony bravia kdl-46x3500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info