Bedienungsanleitung Sony CDP-CE545 (Seite 5 von 88) (Englisch, Französisch, Spanisch)

50453

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Getting StartedGetting Started

Hookups

When connecting an audio cord, be sure to match the

color-coded cord to the appropriate jacks on the

components: Red (right) to Red and White (left) to

White. Be sure to make connections firmly to avoid

hum and noise.

z You can adjust the output level to the amplifier Z

Press ANALOG OUT LEVEL +/– on the remote. You can

reduce the output level up to –20 dB.

When you reduce the output level, “

FADE

” appears in the

display.

Note

If you press the ANALOG OUT LEVEL +/– buttons on

the remote while recording, the recording level will

change even when it is preset on the tape deck, etc.

• If you have a digital component such as a digital

amplifier, D/A converter, DAT or MD

Connect the component via the DIGITAL OUT (OPTICAL)

connector using the optical cable (not supplied). Take off

the cap and plug in the optical cable.

Note that you cannot use fading in or out (page 22) and

Time Fade (page 23) functions when making this

connection.

z If you have a Sony component with the CONTROL A1

(or CONTROL A1) jack

Connect the component via the CONTROL A1 (or

CONTROL A1) jack. You can simplify the operation of

audio systems composed of separate Sony components.

For details, refer to the supplementary “CONTROL A1

Control System” instructions.

z When using another Sony CD player in conjunction

with this player Z

You can set the supplied remote to be effective on this

player only.

• If the other player’s command mode can be set:

Set the CD1/2/3 switch of this player’s remote to CD1

(factory setting), and set the other player’s remote to

CD2 or CD3.

• If the other player’s command mode cannot be set:

Set the CD1/2/3 switch of this player’s remote to CD2

or CD3.

If you connect this player with another Sony CD

player, you have to set the command mode of each

player. For details, see “Connecting Another CD

Player” on page 6.

Setting the voltage selector (voltage

selector equipped models only)

Check that the voltage selector on the rear panel of the

player is set to the local power line voltage. If not, set

the selector to the correct position using a screwdriver

before connecting the AC power cord to a wall outlet.

Connecting the AC power cord

Connect the AC power cord to a wall outlet.

Transporting the player

Before transporting the player, follow the procedure

below to return the internal mechanisms back to their

original position.

1 Remove all the discs from the disc tray.

2 Press A OPEN/CLOSE to close the disc tray.

“–NO DISC–” appears in the display.

3 Wait for 10 seconds, then press POWER to turn off

the player.

AmplifierCD player

POC-15

Optical cable (not supplied)

Note

When you connect via the DIGITAL OUT (OPTICAL)

connector, noise may occur when you play CD software other

than music, such as a CD-ROM.

CD player Digital component

ANALOG

IN OUT

INPUT

2ND

DIGITAL

INPUT

OPTICAL

DIGITAL

OUT

OPTICAL

110 - 120 V220 - 240 V

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony CDP-CE545 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony CDP-CE545

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info