Bedienungsanleitung Sony CDP-CX250 (Seite 5 von 93) (Englisch, Französisch, Spanisch, Schwedisch)

50476

Zoom out

Zoom in

Vorherige Seite

1/93

Nächste Seite

Playing CDsGetting Started

Getting Started

CD player Amplifier

Hookups

When connecting the audio cord, be sure to match the

color-coded cord to the appropriate jacks on the

components: Red (right) to Red and White (left) to

White. Be sure to make connections firmly to avoid

hum and noise.

INPUT

LINE OUT

• If you have a Sony receiver (amplifier) equipped with

the CONTROL A1 jack

Be sure to connect the player to the CD IN jacks on the

receiver (amplifier). When making this connection, set the

COMMAND MODE of the player to CD1 (see the

illustration below). If you further connect the player and

the receiver (amplifier) via the CONTROL A1 jacks with the

CONTROL A1 cord (supplied for canadian models only),

you can use the Auto Function feature between these

components. For details, refer to the supplementary

“CONTROL-A1 Control System” instructions and the

instructions supplied with the receiver (amplifier).

• If you have a digital component such as a digital

amplifier, D/A converter, DAT or MD

Connect the component via the DIGITAL OUT (OPTICAL)

connector using an optical cable (not supplied). Take off the

cap and plug in the optical cable.

POC-15

Optical cable (not supplied)

CD player

Digital component

Note

When you connect via the DIGITAL OUT (OPTICAL)

connector, noise may occur when you play CD software

other than music, such as a CD-ROM.

DIGITAL OUT

OPTICAL

DIGITAL INPUT

OPTICAL

When to use the COMMAND MODE selector

The COMMAND MODE selector is set to CD1 at the

factory for normal use. You can control this player by

connecting to a Sony CD Player with the player control

function, via the CONTROL A1 jacks. When making this

connection, set the COMMAND MODE selectors of each

player to the appropriate position according to the

connected line input jacks. For details, refer to the

instructions supplied with the connected player.

COMMAND MODE

123

When using another Sony CD player together with

this player

You can make the supplied remote effective only for this

player.

• When using the player equipped with the

COMMAND MODE selector:

Set the COMMAND MODE selector of this player to

CD1 and that of another player to CD2 or CD3. Then

set the CD1/2/3 switch on the remote supplied for

each player accordingly.

• When using the player not equipped with the

COMMAND MODE selector:

The command mode of the player without the

COMMAND MODE selector is set to CD1. Set the

COMMAND MODE selector of this player to CD2, and

set the CD1/2/3 switch on the remote to CD2.

Setting the VOLTAGE SELECTOR (except for

European, Canadian and Singaporean

models)

Check that the VOLTAGE SELECTOR on the rear

panel of the player is set to the local power line

voltage. If not, set the selector to the correct position

using a screwdriver before connecting the AC power

cord to a wall outlet.

110 - 120 V 220 - 240 V

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony CDP-CX250 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony CDP-CX250

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info