Bedienungsanleitung Sony CDP-CX53 (Seite 5 von 20) (Englisch)

50522

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Playing CDsGetting Started

Getting Started

Hookups

When connecting the audio cord, be sure to match the

color-coded cord to the appropriate jacks on the

components: Red (right) to Red and White (left) to

White. Be sure to make connections firmly to avoid

hum and noise.

CD player Amplifier

INPUT

LINE

OUT

Setting the voltage selector (voltage

selector equipped models only)

Check that the voltage selector on the rear panel of the

player is set to the local power line voltage. If not, set

the selector to the correct position using a screwdriver

before connecting the AC power cord to a wall outlet.

220 - 240 V110 - 120 V

• If you have a Sony receiver (amplifier) equipped with

the CONTROL A1 jack

Be sure to connect the player to the CD IN jacks on the

receiver (amplifier). When making this connection, set the

COMMAND MODE of the player to CD1. If you further

connect the player and the receiver (amplifier) via the

CONTROL A1 jacks with the CONTROL A1 cord (supplied

for Canadian models only), you can use the Auto Function

feature between these components. For details, refer to the

supplementary “S-Link

/CONTROL-A1 Control System”

instructions and the instructions supplied with the receiver

(amplifier).

When using another Sony CD player together with

this player

You can make the supplied remote effective only for this

player.

• When using the player equipped with the

COMMAND MODE selector:

Set the COMMAND MODE selector of this player to

CD1 and that of another player to CD2 or CD3. Then

set the CD1/2/3 switch on the remote supplied for

each player accordingly.

• When using the player not equipped with the

COMMAND MODE selector:

The command mode of the player without the

COMMAND MODE selector is set to CD1. Set the

COMMAND MODE selector of this player to CD2, and

set the CD1/2/3 switch on the remote to CD2.

COMMAND MODE

123

• If you have a digital component such as a digital

amplifier, D/A converter, DAT or MD

Connect the component via the DIGITAL OUT (OPTICAL)

connector using an optical cable (not supplied). Take off the

cap and plug in the optical cable.

POC-15

Optical cable (not supplied)

CD player Digital component

Note

When you connect via the DIGITAL OUT (OPTICAL)

connector, noise may occur when you play CD software

other than music, such as a CD-ROM.

DIGITAL

OUT

OPTICAL

DIGITAL INPUT

OPTICAL

When to use the COMMAND MODE selector

The COMMAND MODE selector is set to CD1 at the

factory for normal use. You can control this player by

connecting to a Sony CD player with the player control

function, via the CONTROL A1 jacks. When making this

connection, set the COMMAND MODE selectors of each

player to the appropriate position according to the

connected line input jacks. For details, refer to the

instructions supplied with the connected player.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony CDP-CX53 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony CDP-CX53

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info