Bedienungsanleitung Sony CDP-XB820 (Seite 16 von 64) (Englisch, Französisch, Spanisch)

50573

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Recording From CDs

1 Press EDIT/TIME FADE before you start playing

as follows:

• To select Time Edit, press the button until

“EDIT” appears and “A” of “TAPE A” flashes in

the display.

• To select Just Edit, press the button until

“JUST EDIT” appears and “A” of “TAPE A”

flashes in the display.

2 Press 0 or ) to specify the tape length.

Each time you press these buttons, the display

changes as shown below with the tape length of

one side .

n HALF ˜ C-46 23.00 ˜ C-54 27.00 ˜ C-60 30.00 N

n - -. - - ˜ C-90 45.00 ˜ C-74 37.00 N

Recording a CD by Specifying

Tape Length

(Time Edit/Just Edit)

You can have the player create a programme that will

fit the length of the tape. Select one of the following

options:

• Time Edit: automatically creates a programme,

keeping the original order of the disc. However,

when the remaining time becomes shorter than the

next succeeding track, the player automatically

programmes a track which is nearly equal to the

remaining time.

• Just Edit: automatically arranges the track order to fit

the tape length.

The programme may contain up to 24 tracks (a pause

inserted between tracks is counted as one track).

Note that tracks numbered over 24 cannot be

programmed in this feature.

EDIT/TIME FADE

0/)

When tracks, which aren’t numerically consecutive on

the disc, are programmed consecutively (i.e. 1, 3, 5

etc.)

A one-second access time blank is added between the

tracks.

When you select “HALF”

The player divides the total playing time of the disc in

half, keeping the original order (only in Time Edit).

Note that you cannot select “HALF” when the disc has

more than 24 tracks.

3 Press EDIT/TIME FADE to have the player create

the programme.

The music calendar shows the tracks to be

recorded. “B” of “TAPE B” flashes in the display.

4 When you record on both sides of the tape, press

EDIT/TIME FADE again.

The player inserts a pause, then creates the

programme for side B. The display shows the

programmed tracks.

When you record on one side of the tape or on a

DAT or MD, skip this step.

5 Start recording on the deck and then press · on

the player.

When you record on both sides of the tape, the

player pauses at the end of the programme for side

6 When you record on side B, reverse the tape and

press · or P on the player to resume playing.

To cancel Time Edit/Just Edit

Press PLAY MODE.

When using the remote, press CONTINUE.

You can specify the tape length freely in Step 2

You can set the tape length using ≠ AMS ±.

Example: When the tape length of one side is 30 minutes

and 15 seconds

1 To set the minutes, turn ≠ AMS ± until

“30” appears in the display, then push

≠ AMS ±.

2 To set the seconds, turn ≠ AMS ± until

“15” appears in the display, then push

≠ AMS ±.

When tracks, which aren’t numerically consecutive on

the disc, are programmed consecutively (i.e. 1, 3, 5

etc.)

A one-second access time blank is added between the

tracks.

To check and change your programme

See page 15.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony CDP-XB820 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony CDP-XB820

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info