Bedienungsanleitung Sony CDX-GT383A (Seite 11 von 104) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

452379

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

• If the sensor detects a new vibration within 10

seconds after entering the Small Alarm mode, the

alarm sound will gradually become louder.

In 15 seconds, the alarm sound will reach the

maximum and will last 45 seconds, then it will

return to the Security mode (Loud Alarm mode).

Note

If the Loud Alarm mode occurs 10 times, the security

alarm function is automatically turned off to prevent

battery drain.

Canceling the security alarm

function

Attach the front panel, or set the car ignition

switch to the ACC position.

When you cancel the security alarm function, the

unit displays the number of times that the Loud

Alarm mode has functioned due to vibration/

sound to your car.

If the unit enters the Loud Alarm mode 10 times,

“SECU OFF” is displayed.

Adjusting the security settings

1 Press and hold the select button.

The setup display appears.

2 Press the select button repeatedly

until the security alarm settings

appear.

3 Rotate the control dial to select the

setting.

4 Press and hold the select button.

The setup is complete and the display returns

to normal play/reception mode.

The following items can be set:

Other functions

Changing the sound settings

Adjusting the sound

characteristics — BAL/FAD/SUB

You can adjust the balance, fader, and subwoofer

volume.

1 Press the select button repeatedly

until “BAL,” “FAD” or “SUB” appears.

The item changes as follows:

LOW*

t MID*

t HI*

BAL (left-right) t FAD (front-rear) t

SUB (subwoofer volume)*

t AUX*

*1 When EQ3 is activated (page 11).

*2 When the audio output is set to “SUB”

(page 12).

“ATT” is displayed at the lowest setting, and can

be adjusted up to 21 steps.

*3 When AUX source is activated (page 13).

2 Rotate the control dial to adjust the

selected item.

After 5 seconds, the setting is complete and

the display returns to normal play/reception

mode.

Customizing the equalizer curve

— EQ3

“CUSTOM” of EQ3 allows you to make your

own equalizer settings.

1 Select a source, then press (EQ3)

repeatedly to select “CUSTOM.”

2 Press the select button repeatedly

until “LOW,” “MID” or “HI” appears.

3 Rotate the control dial to adjust the

selected item.

The volume level is adjustable in 1 dB steps,

from –10 dB to +10 dB.

Repeat steps 2 and 3 to adjust the equalizer

curve.

To restore the factory-set equalizer curve,

press and hold the select button before the

setting is complete.

After 5 seconds, the setting is complete and

the display returns to normal play/reception

mode.

Tip

Other equalizer types are also adjustable.

S.LED (Security LED)

Activates the blinking LED of the Security

mode: “ON,” “OFF.”

S.TIME (Security alarm start time)

Selects the time from detaching the front panel

to entering in the Security mode: “15S

(seconds),” “1M (minute),” “3M (minutes).”

S.SENS (Security alarm sensitivity)

Selects the vibration detection sensitivity:

“LOW,” “MID,” “HI.”

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony CDX-GT383A Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info