Bedienungsanleitung Sony cmt c 7 nt (Seite 59 von 64) (Englisch)

158796

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Additional Information

The sound skips.

• Replace the MD.

• Try moving the system to a place without

vibration (e.g., on top of a stable stand).

• Try moving the speakers away from the system,

or placing them on separate stands.

When you listen to a track with bass sounds at

high volume, the speaker vibration may cause the

sound to skip.

• Load the disc and wait for 10 to 20 minutes with

the system turned on.

Play does not start from the first track.

• Press PLAY MODE on the remote repeatedly

until “PROGRAM” or “SHUF” disappears to

return to normal play.

“—OVER—” appears.

• Press and hold m or press . to return to the

desired playing position.

“OVER” lights up during recording.

• Set the volume of the connected component

lower.

Recording or editing was done, but the TOC is

not updated.

• MD recording and editing contents are recorded

to the MD when the MD is removed, so make

sure you remove the MD after recording or

editing (see pages 19 and 29).

Recording is not possible.

• Remove the MD and slide the tab to close the

slot (see page 19).

• Connect the optional A/V component properly

(see page 49).

• Switch to another sound source.

• Replace the MD with a recordable MD, or use

Erase Function to erase unnecessary tracks (see

page 34).

The sound from an MD you recorded is too low

(or too high).

• Readjust the recording level (see page 26 or 40).

Tuner

There is severe hum or noise (“TUNED” or

“STEREO” flashes).

• Set the proper band and frequency (see page 42).

• Connect the antenna properly (see page 6).

• Find a place and an orientation that provide good

reception, then set up the antenna again.

If you cannot obtain good reception, we

recommend you connect a commercially

available external antenna.

• The supplied antenna receives signals along its

entire length, so make sure you extend it fully.

• Locate the antennas as far away from the speaker

cords as possible.

• Consult your nearest Sony dealer if the supplied

AM antenna wire has come off the plastic stand.

• Try turning off surrounding electrical equipment.

A stereo FM program cannot be received in

stereo.

• Press FM MODE on the remote until “MONO”

disappears from the display.

• See “There is severe hum or noise (“TUNED” or

“STEREO” flashes)”, and check the antenna

condition.

Cyclical static noise is heard while recording on

an MD.

• Adjust the antenna orientation and position until

the noise stops.

Personal Computer

There is no sound or the sound is too low.

• Be sure to turn up the volume moderately with

the software, and then adjust the volume on the

system.

The sound skips or the operation is unstable.

• Connect the system to the personal computer

directly with the supplied USB cable. Do not

connect the system to the computer through a

USB hub.

The buttons are disabled.

• Press NET MD to turn off the Net MD function.

“Windows cannot locate the driver” appears.

• Install the device driver.

continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony cmt c 7 nt Seite 59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony cmt c 7 nt

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info