Bedienungsanleitung Sony cmt cpx22 (Seite 29 von 36) (Englisch)

158982

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Troubleshooting

Tuner

Severe hum or noise/stations cannot be

received.

• Set the proper band and frequency (page 12).

• Connect the antenna properly (page 6).

• Find a place and an orientation that provide good

reception, then set up the antenna again. If you

cannot obtain good reception, we recommend you

connect a commercially available external

antenna.

• The supplied FM lead antenna receives signals

along its entire length, so make sure you extend it

fully.

• Locate the antennas as far away from the speaker

cords as possible.

• Consult your nearest Sony dealer if the supplied

AM antenna has come off the plastic stand.

• Try turning off surrounding electrical equipment.

• Set “CD POWER OFF” by CD power manage

function (page 13).

A stereo FM program cannot be received in

stereo.

• Press FM MODE until “MONO” disappears.

Tape deck

After pressing nN, there is a mechanical

noise, “Eject” appears in the display, and the

unit enters standby mode automatically.

• Insert the cassette correctly.

The tape does not record or play, or there is a

decrease in sound level.

• The heads are dirty. Clean them (page 32).

• The record/playback heads are magnetized.

Demagnetize them (page 32).

The tape does not erase completely.

• The record/playback heads are magnetized.

Demagnetize them (page 32).

There is excessive wow or flutter, or the sound

drops out.

• The capstans in the tape deck are dirty. Clean

them (page 32).

Noise increases or the high frequencies are

erased.

• The record/playback heads are magnetized.

Demagnetize them (page 32).

The tape does not record.

• No cassette is loaded. Load a cassette.

• The tab has been removed from the cassette.

Cover the broken tab with adhesive tape

(page 32).

• The tape has wound to the end.

Optional components

There is no sound.

• Refer to General item “The clock setting/radio

presetting/timer is canceled.” (page 27) and check

the condition of the system.

• Connect the component properly (page 25) while

checking:

– if the cords are connected properly.

– if the cord plugs are firmly inserted all the way.

• Turn on the connected component.

• Refer to the operating instructions supplied with

the connected component and start playing.

• Press FUNCTION repeatedly to select “MD” or

“VIDEO” (page 26).

The sound is distorted.

• Set the volume of the connected component

lower.

If the system still does not

operate properly after performing

the above measures, reset the

system as follows:

1 Disconnect the power cord.

2 Reconnect the power cord.

3 Press ?/1 to turn on the system.

4 Press x, DIMMER and ?/1 on the unit.

The system is reset to the factory settings. You

should set the settings you made, such as the

preset stations, clock, and timer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony cmt cpx22 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony cmt cpx22

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info