Bedienungsanleitung Sony cmt dx 2 d (Seite 44 von 60) (Englisch)

159316

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Should you encounter a problem with your

system, do the following:

1 Make sure the power cord and speaker

cords are correctly and firmly connected.

2 Find your problem in the troubleshooting

checklist below and take the indicated

corrective action.

If the problem persists after doing all of the

above, consult your nearest Sony dealer.

Note that if service personnel changes some

parts during repair, these parts may be retained.

General

“– –:– –” appears in the display.

• A power interruption has occurred. Set the clock

(page 13) and timer settings (pages 35 and 36)

again.

The clock setting/radio presetting/timer is

canceled.

• Redo the following:

– “Setting the clock” (page 13)

– “Presetting radio stations” (page 28)

– “Falling asleep to music” and “Waking up to

music” (page 35)

– “Timer recording radio programs” (page 36)

There is no sound.

• Press VOLUME +.

• Make sure the headphones are not connected.

• Check the speaker connections (page 10).

• There is no audio output during Rec Timer.

• The system is in pause mode or in slow-motion

play mode. Press H (or DVD NX on the unit)

to return to Normal Play.

• Set “Dolby Digital” or “DTS” under “AV” to

“PCM.”

There is severe hum or noise.

• Move the system away from the source of noise.

• Connect the system to a different wall outlet.

• Install a noise filter (commercially available) to

the power cord.

The timer cannot be set.

• Set the clock again (page 13).

The timer does not function.

• Check the timer setting and set the correct time

(pages 35 and 36).

• Cancel the Sleep Timer function (page 35).

The remote does not function.

• Remove the obstacle.

• Move the remote closer to the system.

• Point the remote at the system’s sensor.

• Replace the batteries (R6/size AA).

• Locate the system away from the fluorescent light.

There is acoustic feedback.

• Reduce the volume.

• Move the microphone away from the speakers or

change the direction of the microphone (CMT-

SX2D Asian and Oceanian models only).

Troubleshooting

Problems and remedies

When the ?/1 indicator flashes

Immediately unplug the power cord and

check the following items.

• If your system has a voltage selector, is the

voltage selector set to the correct voltage?

Check the voltage for your region, then

make sure the voltage selector is set

correctly.

• Are the + and – speaker cords short-

circuited?

• Are you using the supplied speakers?

• Is anything blocking the ventilation holes

on the rear of the system?

Check all the above items and fix any

problems found. After ?/1 indicator stops

flashing, reconnect the power cord and turn

on the system. If the indicator still flashes, or

if the cause of the problem cannot be found

even after checking all the above items,

consult your nearest Sony dealer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony cmt dx 2 d Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony cmt dx 2 d

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info