Bedienungsanleitung Sony cmt l1 (Seite 25 von 28) (Englisch)

158827

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Troubleshooting

Tuner

There is severe hum or noise (“TUNED” or

“STEREO” flashes).

• Set the proper band and frequency (see page 16).

• Connect the antenna properly (see page 7).

• Find a place and an orientation that provide good

reception, then set up the antenna again.

If you cannot obtain good reception, we

recommend you connect a commercially

available external antenna.

• The supplied FM wire antenna receives signals

along its entire length, so make sure you extend

it fully.

• Locate the antennas as far away from the speaker

cords as possible.

• Consult your nearest Sony dealer if the supplied

AM antenna wire has come off the plastic stand.

• Try turning off surrounding electrical equipment.

A stereo FM program cannot be received in

stereo.

• Press FM MODE on the remote until “MONO”

disappears from the display.

• See “There is severe hum or noise (“TUNED” or

“STEREO” flashes).”, and check the antenna

condition.

Optional components

There is no sound.

• Refer to General item “There is no sound.” on

page 24 and check the condition of the system.

• Connect the component properly (see page 22)

while checking:

– if the cords are connected properly.

– if the cord plugs are firmly inserted all the way.

• Turn on the connected component.

• Refer to the operating instructions included with

the connected component and start playing.

• Press FUNCTION repeatedly until “MD” (or

“TAPE”) appears in the display.

The sound is distorted.

• Set the volume of the connected component

lower.

If the system still does not operate

properly after performing the above

measures, reset the system as

follows:

With the system turned on, press DISPLAY,

TUNER/BAND and FUNCTION at the same

time.

“COLD RESET” appears in the display and the

system turns off. All system parameters are

reset to their factory settings. Afterwards, be

sure to do the followings procedures again:

presetting the radio stations, setting the clock

and the timer, and labelling the CD.

Note

You cannot reset the system in the Power Saving

Mode.

Self-diagnosis display

Messages

One of the following messages may appear or

flash in the display during operations.

Complete!

CD editing (Disc Memo) finished normally.

File Full

There are already 100 disc titles stored in the

system.

Initialize

The system is being initialized. You cannot load a

CD during this time. Wait until “Initialize”

disappears from the display.

No Disc

There is no disc in the CD player.

—OVER—

You have reached the end of the CD while

pressing and holding down M during playing

pause.

Push STOP!

You pressed PLAY MODE/TUNING MODE

during playback.

Step Full!

You tried to program 26 tracks (steps) or more.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony cmt l1 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony cmt l1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info