Bedienungsanleitung Sony cmt m 373 nt (Seite 56 von 68) (Englisch)

158985

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Tuner

Severe hum or noise/stations cannot be

received.

• Set the proper band and frequency (page 36).

• Connect the aerial properly (page 5).

• Find a place and an orientation that provide good

reception, then set up the aerial again. If you

cannot obtain good reception, we recommend you

connect a commercially available external aerial.

• The supplied FM lead aerial receives signals

along its entire length, so make sure you extend it

fully.

• Locate the aerials as far away from the speaker

cords as possible.

• Consult your nearest Sony dealer if the supplied

AM aerial has come off the plastic stand.

• Try turning off surrounding electrical equipment.

A stereo FM program cannot be received in

stereo.

• Press FM MODE until “STEREO” appears in the

display.

Cyclical static noise is heard while recording

on an MD.

• Adjust the aerial orientation and position until the

noise stops.

Tape deck

The tape does not record or play, or there is a

decrease in sound level.

• The heads are dirty. Clean them (page 62).

• The record/playback heads are magnetised.

Demagnetise them (page 62).

The tape does not erase completely.

• The record/playback heads are magnetised.

Demagnetise them (page 62).

There is excessive wow or flutter, or the sound

drops out.

• The capstans in the tape deck are dirty. Clean

them using a cleaning cassette.

Noise increases or the high frequencies are

erased.

• The record/playback heads are magnetised.

Demagnetise them (page 62).

The tape does not record.

• No cassette is loaded. Load a cassette.

• The tab has been removed from the cassette.

Cover the broken tab with adhesive tape

(page 62).

• The tape has wound to the end.

Personal computer

The sound skips or the operation is unstable.

• Connect the system to the personal computer

directly with the supplied USB cable. Do not

connect the system to the computer through a

USB hub.

The buttons are disabled.

• Press NET MD to turn off the Net MD function.

“Windows cannot locate the driver” appears.

• Install the device driver.

Optional components

There is no sound.

• Refer to General item “There is no sound.”

(page 54) and check the condition of the system.

• Connect the component properly (page 52) while

checking:

– if the cords are connected properly.

– if the cord plugs are firmly inserted all the way.

• Turn on the connected component.

• Refer to the operating instructions supplied with

the connected component and start playing.

• Press FUNCTION repeatedly to select

“OPTICAL IN” or “ANALOG IN” (page 53).

The sound is distorted.

• Set the volume of the connected component

lower.

• Adjust the recording level lower.

There is no sound from the MD deck.

• Play the MD on an MD deck that supports MDLP

mode (page 22).

• Record the MD again with the recording mode set

to normal length stereo or monaural recording

(page 15).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony cmt m 373 nt Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony cmt m 373 nt

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info