Bedienungsanleitung Sony cmt m 90 dvd (Seite 49 von 60) (Englisch)

158807

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Troubleshooting

continued

Tape Deck

The tape does not record or play, or there is a

decrease in sound level.

• The heads are dirty. Clean them.

• The record/playback heads are magnetised.

Demagnetise them (see page 52).

The tape does not erase completely.

• The record/playback heads are magnetised.

Demagnetise them (see page 52).

There is excessive wow or flutter, or the sound

drops out.

• The capstans in the tape deck are dirty. Clean

them using a cleaning cassette (see page 52).

Noise increases or the high frequencies are

erased.

• The record/playback heads are magnetised.

Demagnetise them (see page 52).

The tape does not record.

• No cassette is loaded. Load a cassette.

• The tab has been removed from the cassette.

Cover the broken tab with adhesive tape (see

page 52).

• The tape has wound to the end.

Optional components

There is no sound.

• Refer to General item “There is no sound.” on

page 47 and check the condition of the system.

• Connect the component properly (see page 45)

while checking:

– if the cords are connected properly.

– if the cord plugs are firmly inserted all the way.

• Turn on the connected component.

• Refer to the operating instructions supplied with

the connected component and start playing.

The sound is distorted.

• Set the volume of the connected component

lower.

The sound from the component connected to the

AUDIO IN MD (VIDEO) jacks is distorted.

• If “VIDEO” appears when you press

FUNCTION repeatedly, switch the function to

“MD” (see the tip for “Listening to audio from a

connected component” on page 46).

Tuner

Severe hum or noise/stations cannot be

received.

• Set the proper band and frequency (see page 33).

• Connect the antenna properly (see page 9).

• Find a place and an orientation that provide good

reception, then set up the antenna again. If you

cannot obtain good reception, we recommend

you connect a commercially available external

antenna.

• The supplied FM lead antenna receives signals

along its entire length, so make sure you extend

it fully.

• Locate the antennas as far away from the speaker

cords as possible.

• Consult your nearest Sony dealer if the supplied

AM antenna has come off the plastic stand.

• Try turning off surrounding electrical

equipments.

A stereo FM program cannot be received in

stereo.

• Press REPEAT/FM MODE until “STEREO”

appears in the display.

If the system still does not operate

properly after performing the above

measures, reset the system as

follows:

1 Disconnect the mains lead.

2 Reconnect the mains lead.

3 Press ?/1 to turn on the system.

4 Press ?/1 while pressing x and z REC.

The system is reset to the factory settings

except for DVD settings. You should set the

settings you made, such as the preset stations,

clock, and timer.

To reset the DVD settings, select “RESET” in

step 3 of “Using the Setup Display” (page 19).

After you select “RESET” and press ENTER,

select “YES”, then press ENTER to reset the

settings (it takes a few seconds to complete).

Do not press ?/1 when resetting the system.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony cmt m 90 dvd Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony cmt m 90 dvd

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info