Bedienungsanleitung Sony cmt m100md s (Seite 59 von 64) (Englisch)

158790

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Additional Information

The sound skips.

• Replace the MD.

• Try moving the system to a place without

vibration (e.g., on top of a stable stand).

• Try moving the speakers away from the system,

or placing them on separate stands.

When you listen to a track with bass sounds at

high volume, the speaker vibration may cause the

sound to skip.

• Insert the disc and wait for 10 to 20 minutes with

the system turned on.

Play does not start from the first track.

• Press PLAY MODE/DIRECTION (or PLAY

MODE on the remote) repeatedly until both

“PGM” and “SHUF” disappear to return to

normal play.

“OVER” appears.

• You have reached the end of the MD. Press and

hold m or press . to return to the desired

playing position.

“OVER” lights up during recording.

• Adjust the recording level lower (see page 29).

Recording or editing was done, but the TOC is

not updated.

• MD recording and editing contents are recorded

to the MD when the MD is removed, so make

sure you remove the MD after recording or

editing (see pages 20 and 30).

Recording is not possible.

• Remove the MD and slide the tab to close the

slot (see page 20).

• Connect the optional component properly (see

page 53).

• Switch to another sound source.

• Replace the MD with a recordable MD, or use

the Erase Function to erase unnecessary tracks

(see page 35).

The sound from an MD you recorded is too low

(or too high).

• Readjust the recording level (see page 41).

Tape Deck

The tape does not record.

• No cassette is loaded. Load a cassette.

• The tab has been removed from the cassette.

Cover the broken tab with adhesive tape (see

page 55).

• The tape has wound to the end.

The tape does not record or play, or there is a

decrease in sound level.

• The heads are dirty. Clean them.

• The record/playback heads are magnetised.

Demagnetise them (see page 55).

The tape does not erase completely.

• The record/playback heads are magnetised.

Demagnetise them (see page 55).

There is excessive wow or flutter, or the sound

drops out.

• The capstans in the tape deck are dirty. Clean

them using a cleaning cassette (see page 55).

Noise increases or the high frequencies are

erased.

• The record/playback heads are magnetised.

Demagnetise them (see page 55).

Optional components

There is no sound.

• Refer to General item “There is no sound.” on

page 57 and check the condition of the system.

• Connect the component properly (see page 53)

while checking:

– if the cords are connected properly.

– if the cord plugs are firmly inserted all the way.

• Turn on the connected component.

• Refer to the operating instructions included with

the connected component and start playing.

The sound is distorted.

• Adjust the recording level lower (see page 29).

continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony cmt m100md s Seite 59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony cmt m100md s

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info