Bedienungsanleitung Sony DAR-RH1000 (Seite 16 von 536) (Spanisch, Polnisch)

6508

Zoom out

Zoom in

Vorherige Seite

1/536

Nächste Seite

– Very humid.

– Subject to vibration.

– Subject to direct sunlight.

• Do not connect any speakers other than those supplied

with this system.

• Use caution when placing the speakers and/or speaker

stands (not supplied) attached to the speakers on a

specially treated floor (waxed, oiled, polished, etc.), as

staining or discoloration may result.

• Cover the floor with a cloth when connecting.

• Be sure to match the speaker cord polarity with the

component terminals: 3 to 3 (grey), # to # (black).

If reversed, the sound will lack bass and may be

distorted.

Notes on speaker cord treatment

• Do not insert the speaker cord insulation in the

speaker terminals. Bend the stripped cord at the

insulation before connecting.

• To avoid short-circuiting the speakers, make

sure speaker cord conductors do not touch the

neighbouring conductors or terminal.

Example:

After connecting the system components and the

mains leads, you can check for a speaker short-

circuit using the test tone (page 102). If the test

tone is not output, or is output from a speaker other

than indicated in the front panel display, check the

speaker connection.

Note

If you connect the speakers incorrectly, or turn up the

volume while the speakers are short-circuited, the

POWER indicator on the subwoofer flashes and the

system enters standby mode. If this happens, disconnect

the mains lead, wait about two minutes, and then

reconnect to turn on the system.

Positioning the speakers

For the best possible surround sound, all speakers

other than the subwoofer should be the same

distance from the listening position (A).

However, this system allows you to place the

centre speaker up to 1.6 m closer (B) and the

surround speakers up to 4.6 m closer (C) to the

listening position.

The front speakers can be placed from 1.0 to 7.0 m

(A) from the listening position.

Notes

• Do not place the centre speaker and surround speakers

farther away from the listening position than the front

speakers.

• If you change the speaker positions after Easy Setup

(page 34), change the “Distance” and “Size” settings in

“Speaker” setup accordingly (page 100).

Note on subwoofer placement

If the subwoofer is placed too close to a CRT TV

or projector, magnetic leakage may interfere with

the video signals and cause colour irregularity.

Should this happen, turn off the TV or the

projector, wait for 15 to 30 minutes, and then turn

it on again. If the problem persists, try the

following:

– Position the subwoofer at least 0.3 m away from

the TV or the projector.

– Move any nearby magnetic object away from the

subwoofer (healthcare devices, toys, etc.).

Magnetic latches on TV stands may also cause a

problem.

Too much insulation is

removed. Conductors are

touching each other.

Conductors are splayed, and

touching neighbouring

terminal.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony DAR-RH1000 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony DAR-RH1000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info