Bedienungsanleitung Sony DCR-SR36 (Seite 28 von 36) (Englisch)

61549

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Troubleshooting

If you run into any problems using your

camcorder, use the following table to

troubleshoot the problem. If the problem

persists, disconnect the power source and

contact your Sony dealer.

Notes before sending your camcorder for

repair



Your camcorder may require initializing or

change the current hard disk of the camcorder,

depending on the problem. In the event of

this, the data stored on the hard disk will be

deleted. Be sure to save the data on the internal

hard disk (see “Handycam Handbook” (PDF))

on other media (backup) before sending your

camcorder for repair. We will not compensate

you for any loss of hard disk data.



During repair, we may check a minimum

amount of data stored on the hard disk in order

to investigate the problem. However, your Sony

dealer will neither copy nor retain your data.



For the symptoms of your camcorder, see

“Handycam Handbook” (PDF) and for

connecting to the computer, see “PMB Guide.”

The power does not turn on.



Attach a charged battery pack to the

camcorder (p.

8).



Connect the plug of the AC Adaptor to the

wall outlet (wall socket) (p.

8).

The camcorder does not operate even

when the power is set to on.



It takes a few seconds for your camcorder

to be ready to shoot aer the power is

turned on. is is not a malfunction.



Disconnect the AC Adaptor from the wall

outlet (wall socket) or remove the battery

pack, then reconnect it aer about 1

minute. If the functions still do not work,

press the RESET button (p.

17) using a

sharp-pointed object. (If you press the

RESET button, all settings, including the

clock setting, are reset.)



e temperature of your camcorder is

extremely high. Turn o your camcorder

and leave it for a while in a cool place.



e temperature of your camcorder is

extremely low. Turn o the camcorder

and take it to a warm place. Leave the

camcorder there for a while, then turn on

the camcorder.

Your camcorder gets warm.



is is because the power has been

turned on for a long time. is is not a

malfunction.

The power abruptly turns o.



Use the AC Adaptor.



Turn on the power again.



Charge the battery pack (p. 8).

Pressing START/STOP or PHOTO does

not record images.



Set the POWER switch to (Movie) or

(Still) (p.

11).



You cannot record images in sleep mode.

Press the QUICK ON button (p.

18).



Your camcorder is recording the image you

have just shot on the media. You cannot

make new recording during this period.



e media of the camcorder is full. Delete

unnecessary images (p.

24).



Total number of movies or still images

exceeds the recordable capacity of the

media. Delete unnecessary images (p.

24).

The recording stops.



e temperature of your camcorder

is extremely high/low. Turn o your

camcorder and leave it for a while in a

cool/warm place.

You cannot install “Picture Motion

Browser.”



Check the computer environment required

to install “Picture Motion Browser.”



Install “Picture Motion Browser” in an

orderly manner (p.

25).

“Picture Motion Browser” does not

work correctly.



Quit “Picture Motion Browser” and restart

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony DCR-SR36 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony DCR-SR36

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info