Bedienungsanleitung Sony DSX-GS80 (Seite 14 von 108) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Schwedisch)

699364

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

14GB

When connecting to the battery directly

When the amperage rating of the fuse used

on your car is 10 A, make the power

connection to the battery directly to avoid

short circuits.

 to a metal point of car

 to the positive battery terminal

Notes

• Despite connecting to the power supply lead of

the car, the unit may not fully provide its

performance due to insufficient power. In this

case, make the power connection to the battery

directly.

• All power wires connected to the positive battery

post should be fused within 450 mm (18 in) of the

battery post, and before they pass through any

metal.

• Make sure that the car’s battery wires connected

to the car (ground (earth) to chassis)* are of a wire

gauge at least equal to that of the main power

wire connected from the battery to the head unit.

• During full-power operation, a current of more

than 15 A will run through the system. Therefore,

make sure that the wires to be connected to the

+12 V and GND terminals of this unit are at least

14-Gauge (AWG14) or have a sectional area of

more than 2 mm² (

/32 in).

When making the speaker parallel connection, use

wires with more than 12-Gauge (AWG12) or wires

that have a sectional area of more than 3.5 mm²

(

/32 in).

If you have any questions or problems

concerning the connection, consult the

dealer for details.

Memory hold connection

When the yellow power supply lead is

connected, power will always be supplied to

the memory circuit even when the ignition

switch is turned off.

Speaker connection

• Before connecting the speakers, turn the

unit off.

• Use speakers with a 2 Ω impedance or 4 Ω

to 8 Ω impedance, and with adequate

power handling capacities to avoid

damage.

Subwoofer Easy Connection

You can use a subwoofer without a power

amplifier when it is connected to a rear

speaker lead.

To enable the connection, set [SUBW MODE]

in [SUBW DIRECT] to [1] to [3].

Notes

• Preparation of the rear speaker leads is required.

• Use a subwoofer with a 2 Ω impedance or 4 Ω to 8

Ω impedance, and with adequate power handling

capacities to avoid damage.

Speaker Parallel Connection

When making the speaker parallel

connection for a high volume playback, be

sure to:

– Set [SPEAKER LOAD] in [GENERAL] to

[2 OHM].

Notes

• When using a subwoofer with dual voice coil, or

using a subwoofer by connecting the right and left

rear speaker leads, be sure to set [SPEAKER LOAD]

in [GENERAL] to [2 OHM].

• To exert the speaker’s potential, make the power

connection to the battery directly (page 14).

Less than 450 mm (18 in)

+12 V car battery

Fuse (15 A)

Front speaker

Subwoofer

Front speaker

(4 Ω to 8 Ω)

Rear speaker

(4 Ω to 8 Ω)

Subwoofer

(4 Ω to 8 Ω, dual voice

coil type)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony DSX-GS80 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info