Bedienungsanleitung Sony htp 1200 (Seite 36 von 40) (Englisch)

370382

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

masterpage:Left

lename[E:\SEM_Janet\Revision_HTP-

200\J9040000_2103636121HTP1200CEL\2103636121\GB09ADD_HTP-1200-CEL.fm]

model name1[HTP-2000]

model name2[HTP-1200]

103

636

(1)]

The FM reception is poor.

• Use a 75-ohm coaxial cable (not supplied) to

connect the receiver to an outdoor FM antenna as

shown below. If you connect the receiver to an

outdoor antenna, ground it against lightning. To

prevent a gas explosion, do not connect the ground

wire to a gas pipe.

Radio stations cannot be tuned in.

• Check that the antennas are connected securely.

Adjust the antennas and connect an external

antenna if necessary.

• The signal strength of the stations is too weak

(when tuning in with automatic tuning). Use direct

tuning.

• Make sure you set the tuning interval correctly

(when tuning in AM stations with direct tuning).

• No stations have been preset or the preset stations

have been cleared (when tuning by scanning

preset stations). Preset the stations (page 19).

RDS does not work.

• Make sure that you are tuned to an FM RDS

station.

• Select a stronger FM station.

The RDS information that you want does not

appear.

• Contact the radio station and find out whether they

actually provide the service in question. If so, the

service may be temporarily out of order.

There is no picture or an unclear picture

appears on the TV screen or monitor.

• Select the appropriate input on the receiver.

• Set your TV to the appropriate input mode.

• Move your TV away from the audio components.

Remote control

The remote does not function.

• The AUX button on the remote is not available for

receiver operation.

• Point the remote at the remote sensor on the

receiver.

• Remove any obstacles in the path between the

remote and the receiver.

• Replace all the batteries in the remote with new

ones, if they are weak.

• Make sure you select the correct input on the

remote.

• To activate the buttons with orange printing, press

ALT first before pressing the buttons.

• Before you use the V/v/B/b button for receiver

operation, press MAIN MENU. To operate other

components, press TOP MENU/GUIDE or AV

MENU after pressing the function button.

Error message

If there is a malfunction, the display shows a

message.

PROTECT

Irregular current is output from the speakers. The

receiver will automatically turn off after a few

seconds. Check the speaker connection and turn on

the power again. If this problem persists, consult

your nearest Sony dealer.

If you are unable to remedy the

problem using the

troubleshooting guide

Clearing the receiver’s memory may remedy the

problem (page 13). However, note that all

memorized settings will be reset to their factory

settings and you will have to readjust all settings

on the receiver.

If the problem persist

Consult your nearest Sony dealer.

Reference sections for clearing

the receiver’s memory

ANTENNA

Receiver

To ground

Ground wire

(not supplied)

Outdoor FM antenna

To clear See

All memorized settings page 13

Customized sound fields page 27

GB01COV_HTP-1200-CEL.book Page 36 Thursday, September 23, 2004 6:22 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony htp 1200 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony htp 1200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info