Bedienungsanleitung Sony htr 210 ss (Seite 34 von 44) (Englisch)

370546

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

masterpage:Left

lename[D:\Sony SEM

5\Revision_HTR210SS\J9050956_2599618112HTR210SS_GB\2599618112\GB08REM_HTR-

10SS-CEL.fm]

model name1[HTR-210SS]

[2-599-618-11(2)]

Notes

• The supplied remote can be used to control the DVD

recorder if the command modes of the DVD recorder

and remote’s setting are the same. The initial setting

for the remote is “DVD 1”. If you cannot control the

DVD recorder using the remote, you can change

either the factory setting of the remote (see

“Changing the factory setting of an input button” on

page 34) or the command mode of the DVD recorder

(refer to separate operating instructions supplied

with the DVD recorder).

• Some functions explained in this section may not

work depending on the model.

• The above explanation is intended to serve as an

example only. Therefore, depending on the

component the above operation may not be possible

or may operate differently than described.

• When you press input buttons (VIDEO 1, VIDEO 2

or DVD), the input mode of the TV might not switch

to the corresponding input mode that you want. In

this case, press TV/VIDEO button to switch the input

mode of the TV.

• To activate the buttons with orange printing, press

TV and the button you want simultaneously.

If the factory settings of the input buttons do not

match your system components, you can change

them. For example, if you have a CD player and

you do not have a DVD player/DVD recorder, you

can assign the DVD button to your CD player.

1 Hold down the input button whose

input you want to change (for example,

DVD).

2 Press the corresponding button of the

component you want to assign to the

input button (for example, 5 – CD

player).

The following buttons are assigned to select

the input:

*Sony VCRs are operated with a VTR 2 or 3

setting. These correspond to 8 mm and VHS

respectively.

Now you can use the DVD button to control

the CD player.

To reset a button to its factory

setting

Repeat the above procedure.

To reset all the input buttons to

their factory setting

Press ?/1, TEST TONE and MASTER VOL –

at the same time.

Remote

Button

Operations Function

X ws VCR/

CD player/

DVD player/

MD deck/

Tape deck

Pauses playback or

recording. (Also starts

recording with

components in

recording standby.)

x w; VCR/

CD player/

DVD player/

MD deck/

Tape deck

Stops playback.

O wj DVD player Returns to the

previous menu or

exits the menu.

V/v wk Receiver Selects a menu item.

B/b wk Receiver Adjusts or changes

the setting.

V/v/B/b wk VCR/

Satellite tuner/

DVD player

Selects a menu item.

Changing the factory

setting of an input button

To operate Press

VCR (command mode VTR 3*) 1

VCR (command mode VTR 2*) 2

DVD player or

DVD recorder

(command mode DVD 1)

DVD recorder

(command mode DVD 3)

CD player 5

MD deck 6

Tape deck B 7

Tuner (this receiver) 8

DSS (Digital Satellite Receiver) 9

DCS (Digital CS Tuner) 0/10

BSD (Digital BS Tuner) -/--

GB01COV_HTR-210SS-CEL.book Page 34 Wednesday, May 18, 2005 10:15 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony htr 210 ss Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony htr 210 ss

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info