Bedienungsanleitung Sony hvr m25p (Seite 86 von 104) (Englisch)

136405

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

86 Chapter 6 Maintenance

Chapter 6 Maintenance

Symptom Cause/Remedy

When you set AUDIO INPUT LEVEL

switch:

• You do not know how to adjust the input

level.

• The recorded level is too low.

• The recorded sound is distorted.

Audio dubbing cannot be done.

Audio dubbing is interrupted.

No sound or undesired sound is output

from HDMI OUT jack, AUDIO OUT jacks,

or PHONE jack.

Cannot hearCH3 and CH4 audio.

If an i.LINK cable is connected when you

edit the dubbing, the monitor does not

display any image.

The unit does not function as part of a

digital non-linear editing system.

The functions on the unit do not operate.

Confirm the level of the sound output from the player by referring to the player’s

instruction manual. According to that output level, set AUDIO INPUT LEVEL

switch on the rear panel of the unit so as to obtain an optimum level.

If you are not clear about the player’s output level, try the following procedures.

1 Specify the output level by types of audio output connectors available on the

player.

• If the player is equipped with phono jacks: –10.

• If the player is equipped with XLR connectors: +4 or –2.

2 Set AUDIO INPUT switch on the front panel to AUTO and play back the tape

which you intend to use for playback. When the playback audio level is at its

maximum, if the audio levels meters exceed 0 dB, set AUDIO INPUT LEVEL

switch to the lower step (+4). Either, set AUDIO INPUT switch to MANU and

turn AUDIO REC LEVEL control knobs to adjust the recording level. The

recorded sound at the portion where the meters exceed 0 dB will be distorted.

• You are trying to dub the sound onto an HDV or DV-formatted tape.

t Sounds can be dubbed only onto a DVCAM-formatted tape (recorded) in the

32 kHz audio mode (4-channel). If the unit detects the following, audio

dubbing will automatically abort, an alarm message will be superimposed on

LCD monitor and on an external monitor.

–A blank portion

–A section recorded in other than 32 kHz audio mode (4-channel)

–A portion recorded in other than DVCAM format

–A tape displayed as NS.

• You have tried to dub the sound onto channels 1/2.

t Only channels 3/4 can be used for dubbing. You cannot dub the sound onto

channels 1/2.

• When the audio mode is set to 32 kHz (4-channel), you can select the audio

channel to output the sound using the AUDIO OUTPUT SELECT selector on the

front panel. Check the setting of [AUDIO MONI] in [AUDIO SET] menu.

t Set AUDIO OUTPUT SELECT switch to MIX or CH-3/4.

t Use the correct setting for [HDV/DV SEL] in [IN/OUT REC] menu in

accordance with the equipment to be connected.

• The INPUT SELECT switch is set to a setting other than HDV/DV.

t Set it to HDV/DV.

• The editing controller or the editing software is not compatible with the unit.

t Refer to the instruction manuals of the controller or the software and consult

their manufacturers.

Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony hvr m25p Seite 86

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info