Bedienungsanleitung Sony ke-p42m1 (Seite 19 von 260) (Deutsch, Englisch, Holländisch, Französisch)

140020

Zoom out

Zoom in

Vorherige Seite

1/260

Nächste Seite

Safety Information

LCD Screen (KLV-L32M1 only)

• Although the LCD screen is made with high-precision

technology and 99.99% or more of the pixels are effective, black

dots may appear or bright points of light (red, blue, or green)

may appear constantly on the LCD screen. This is a structural

property of the LCD panel and is not a malfunction.

• Do not expose the LCD screen surface to the sun. Doing so may

damage the screen surface.

• Do not push or scratch the front filter, or place objects on top of

this unit. The image may be uneven or the LCD panel may be

damaged.

• If this unit is used in a cold place, a smear may occur in the

picture or the picture may become dark.

This does not indicate a failure. These phenomena disappear as

the temperature rises.

• Ghosting may occur when still pictures are displayed

continuously. It may disappear after a few moments.

• The screen and cabinet get warm when this unit is in use. This is

not a malfunction.

Mains lead

If you damage the mains lead, it may

result in fire or electric shock.

• Do not pinch, bend, or twist the mains

lead excessively. The core lines may

be exposed or cut, causing a short-

circuit which may induce fire or

electric shock.

• Do not convert or damage the mains

lead.

• Do not put anything heavy on the

mains lead. Do not pull the mains

lead.

• Keep the mains lead away from heat sources.

• Be sure to grasp the plug when disconnecting the mains lead.

If the mains lead is damaged, stop using it and ask your dealer or

Sony service centre to exchange it.

Fluorescent lamp (KLV-L32M1 only)

This unit uses a special fluorescent lamp as its light source. If the

screen image becomes dark, flickers, or does not appear, the

fluorescent lamp has run down and should be replaced. For

replacement, consult qualified service personnel.

When not in use

For environmental and safety

reasons, it is recommended that the

unit be switched off when not in

use – not left in standby mode.

Disconnect it from the mains.

Heat

Do not touch the surface of the unit. It remains hot, even after the

unit has been turned off for some time.

Cable wiring

Take care not to catch your feet on the cables. It may damage the

unit.

Cleaning the screen surface

The screen surface is finished with a special coating to prevent

strong light reflections. Be sure to observe the following

precautions to avoid damaging the finish.

• To remove dust from the screen surface, wipe gently with a soft

cloth. If dust is persistent, wipe with a soft cloth slightly

moistened with a diluted mild detergent solution. You can wash

and repeatedly use the soft cloth.

• Never use any type of abrasive pad, alkaline/acid cleaner,

scouring powder, or strong solvent such as alcohol, benzine or

thinner.

Installation

Do not install optional components too close to the unit. Keep

optional components at least 30 cm away from the unit. If a VCR is

installed in front of the unit or beside the unit, the picture may

become distorted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony ke-p42m1 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info