Bedienungsanleitung Sony kf-42sx200 (Seite 36 von 251) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Türkisch)

140211

Zoom out

Zoom in

Vorherige Seite

1/251

Nächste Seite

Problem

No picture (screen is dark), no sound.

Poor or no picture (screen is dark),

but good sound.

Poor picture quality when watching a

RGB video source.

Good picture, no sound

No colour on colour programmes

Distorted picture when changing

programmes or selecting teletext

Striped picture

Noisy picture when viewing TV channel

No unscrambling or unstable picture

whilst viewing a scrambled channel with

a decoder connected through the Scart

connector

3 (SMARTLINK)

Remote control does not function

The lamp indicator on the TVset

flashes.

The standby indicator on the TVset

flashes.

Additional Information

Here are some simple solutions to problems which may affect the picture and sound.

Troubleshooting

Solution

• Plug the TV set in.

• Press the

button on the front of the TV set.

• If the indicator is on in red colour, press

button on the remote

control.

• Check the aerial connection.

• Check that the selected video source is on.

• Turn the TV set off for 3 or 4 seconds and then turn it on again using the

button on the front of the TV set.

• Using the MENU system, select the Picture Adjustment menu. Adjust the

brightness, contrast and colour balance levels.

• Press the button repeatedly on the remote control until the RGB

symbol 1 or 2 is displayed on the screen.

• Press the +/- button on the remote control.

• Check that "Main" speaker is selected in the "Features" menu.

• Using the MENU system, select the Picture Adjustment menu. Adjust the

colour balance.

• Turn off any equipment connected to the Scart connectors on the rear of

the TV set.

• Adjust the RF Attenuator (ATT). For details, please refer to the section

"Using the Further Programme Preset function".

• Adjust Fine Tuning (AFT) to obtain better picture reception. For details,

please refer to the section "Using the Further Programme Preset function"

• Using the menu system, select the “Picture Adjustment” menu and set

“Noise Reduction” to “Auto”.

• Using the menu system, select the “Features” menu and set “AV3 Output”

to “TV”

• Check that the Media Selector on the remote control is set to the device you

are using (VCR, TV or DVD).

• If the remote control does not operate the VCR or DVD even when the

Media Selector has been set correctly. Enter the necessary code set as

explained on “Remote Controll Configuratio for VCR/DVD” chapter of

this instruction manual.

• Replace the batteries.

• Replace the lamp. For details please refer to the section “Replace the

Lamp”

• If you are changing the lamp without disconnecting the power cord, the

standby indicator flashes. To continue changing the lamp, disconnect the

power cord and wait for at least 30 minutes to allow the lamp to cool.

• Check that the lamp cover is tightly attached.

• If you are not changing the lamp but the standby indicator flashes, contact

your nearest Sony service centre.

• If you continue to have these problems, have your TV serviced by qualified personnel.

• NEVER open the casing yourself.

01GBKF50/42SX200.fm Page 37 Tuesday, January 7, 2003 10:23 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony kf-42sx200 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info