Bedienungsanleitung Sony LCD Dtat Projector (Seite 19 von 108) (Englisch, Französisch, Spanisch)

499137

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

19 (GB)

Projecting

INPUT-A:Selects video signal input from the

INPUT A connector.

INPUT-B: Selects video signal input from the

INPUT B connector.

INPUT-C: Selects to display the Windows CE

window.

VIDEO: Selects video signal input from the

VIDEO (VIDEO IN) jack.

S-VIDEO:Selects video signal input from the S

VIDEO (VIDEO IN) jack.

4 Press the FOCUS key then the M or m key on the

Remote Commander to adjust the focus.

“LENS FOCUS” appears on the screen during

adjustment.

5 Press the ZOOM key then the M or m key on the

Remote Commander to adjust the picture size.

“LENS ZOOM” appears on the screen during

adjustment.

6 Press the FOCUS key and arrow keys on the

Remote Commander to adjust the focus again.

7 Press the SHIFT key then the M or m key on the

Remote Commander to adjust the vertical position

of the picture.

“LENS SHIFT” appears on the screen during

adjustment.

Note on focus and zoom adjustments

If the optional VPLL-ZM101, VPLL-ZM31 or VPLL-

FM21 lens is installed, perform the focus and zoom

adjustments manually.

To use the keys on the control panel for

focus, zoom and shift adjustments

Press the LENS CONTROL key repeatedly to display

the adjustment mode you want. Each press changes

the mode, “LENS FOCUS,” “LENS ZOOM” and

“LENS SHIFT” in this order. Then press the arrow

keys to adjust.

Note

Looking into the lens when projecting may cause

injury to your eyes.

Cut off the picture

Press the PIC MUTING key on the Remote

Commander. To restore the picture, press the PIC

MUTING key again.

To get the clearest picture

You can get the suitable picture when a signal from

the computer is input. Press the APA key.

The picture is automatically adjusted to be projected

clearest.

Notes

•Adjust the signal when the still picture is displayed

on the screen.

•Press the APA key when the full image is displayed

on the screen. If there are black edges around the

image, the APA function will not function properly

and the image may extend beyond the screen.

•If you switch the input signal or re-connect a

computer, press the APA key again to get the

suitable picture.

•“ADJUSTING” appears on the screen. To restore the

original screen, press the APA key again during the

adjustment.

•“Complete!” appears on the screen when the picture

is adjusted properly. The picture may not be adjusted

properly depending on the kinds of input signals.

•Adjust the items in the INPUT SETTING menu

when you adjust the picture manually.

For details, see page 23 (GB).

To correct the trapezoid

When the projecting image is a trapezoid, perform the

shift adjustment with the SHIFT key.

If the image is still a trapezoid, correct it in DIGIT

KEYSTONE in the INSTALL SETTING menu.

When the base edge is longer than the upper

edge as shown in the figure below:

When the upper edge is longer than the base

edge as shown in the figure below:

For details on “DIGIT KEYSTONE,” see page 27 (GB).

Set the value to negative.

Set the value to positive.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony LCD Dtat Projector Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony LCD Dtat Projector

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info