Bedienungsanleitung Sony mds-jb980 (Seite 14 von 108) (Englisch, Französisch)

157184

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

To change the trigger level for

Automatic Track Marking

Do the procedure below to change the signal

level that triggers Automatic Track Marking.

1 While the deck is stopped, press MENU/

NO.

2 Turn AMS (or press ./>

repeatedly) until “Setup?” appears,

then press AMS or YES.

3 Turn AMS (or press ./>

repeatedly) until “LS(T)” appears, then

press AMS or YES.

4 Turn AMS (or press ./>

repeatedly) to select the level, then

press AMS or YES.

You can set the level at any value between

–72 dB and 0 dB, in 2 dB increments

(–50 dB is the factory setting).

5 Press MENU/NO.

Tips for automatic track marking

• When recording from a CD player or an MD deck

connected to the DIGITAL IN connector, the entire

material might be recorded as a single track in the

following cases:

— When you consecutively record the same track

two or more times using single-track repeat play.

— When you consecutively record two or more

tracks with the same track number but from

different CDs or MDs.

— When you record tracks from certain CD or

multi-disc players.

• A track number might not be marked for tracks less

than 4 seconds long (in Stereo mode, Monaural

mode, and LP2 Stereo mode) or 8 seconds long (in

LP4 Stereo mode) during recording.

• When recording from a component connected to the

ANALOG IN jacks with “T.Mark Off” selected or

when recording from a DAT deck or DBS tuner

connected to the DIGITAL IN connector, the entire

material may be recorded as a single track.

• When recording from a DAT deck or DBS tuner

connected to the DIGITAL IN connector, the deck

will mark a track number whenever the sampling

frequency of the input signal changes, regardless of

the track marking parameter setting (“T.Mark

LSyn(c)” or “T.Mark Off”).

Tip

You can mark track numbers even after recording has

finished. See “Dividing recorded tracks” on page 28.

Erasing blank portions

automatically (Smart Space/

Auto Cut)

The Smart Space function lets you make the

blank spaces between tracks 3 seconds long

automatically. If the Smart Space function is on

and there is no sound input for about 3 seconds

or more (but less than 30 seconds) while

recording, the deck replaces this silence with a

blank of about 3 seconds and continues

recording.

Auto Cut: When the Smart Space function is

on, if there is no sound input for 30 seconds or

more, the deck replaces this silence with a blank

of about 3 seconds and enters recording pause.

1 While the deck is stopped, press MENU/

NO.

2 Turn AMS (or press ./>

repeatedly) until “Setup?” appears,

then press AMS or YES.

3 Turn AMS (or press ./>

repeatedly) until “S.Space On” appears,

then press AMS or YES.

No sound input for less than 30 seconds

Replaced with a blank of 3 seconds and

recording continues

Off

No sound input for 30 seconds or more

Replaced with a blank of 3 seconds

and recording pauses

Off

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony mds-jb980 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony mds-jb980

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info