Bedienungsanleitung Sony mds-je780 (Seite 14 von 56) (Englisch)

157185

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Tips

• The MDLP indicator lights up when you select LP2

or LP4 in step 2 above.

• The deck is set at the factory to add “LP:” at the

beginning of a track name automatically. This

indication is displayed when the track is played on a

deck that does not support long-time recording.

To turn off this function, do the following procedure.

1 While the deck is stopped, playing, or

paused, press MENU/NO.

2 Turn AMS (or press ./> repeatedly)

until “Setup?” appears, then press AMS or

YES.

3 Turn AMS (or press ./> repeatedly)

until “LPstamp On” (factory setting)

appears, then press AMS or YES.

4 Turn AMS (or press ./> repeatedly)

to select “LPstamp Off”, and then press

AMS or YES.

5 Press MENU/NO.

To add “LP:” automatically again, select “LPstamp

On” in step 4 above.

Notes

• The recorded “LP:” is a stamp which appears to

indicate that the track cannot be played back when

you try to play the track on a system that does not

support MDLP mode. It does not appear for systems

that support MDLP mode.

• When set to “On”, “LP:” is recorded as the track

name, so the number of characters that can be input

to an MD is reduced. If you divide an “LP:” track

using the Divide function, “LP:” is also added to the

latter track.

• The selected recording mode is kept even after

recording has finished, so be sure to check the

recording mode before recording.

• Tracks recorded in MDLP (LP2 or LP4) Stereo

mode cannot be played back on a system that does

not support MDLP mode.

• Even if you press REC MODE during recording,

you cannot change the recording mode.

• Even if you press REC MODE repeatedly to select

MONO, the monitor signal during recording does

not become monaural.

• You cannot use S.F Edit and some other MD edit

functions for tracks recorded in MDLP mode.

Marking track numbers while

recording

— Manual/Automatic Track Marking

You can mark track numbers either manually or

automatically while recording. By marking

track numbers at specific points, you can

quickly locate the points later or edit the MD

easily.

Marking track numbers manually

(Manual Track Marking)

While recording, press REC z at the point

where you want to add a track number.

Marking track numbers automatically

(Automatic Track Marking)

When recording from a CD player or MD deck

connected to a DIGITAL IN connector, the deck

marks track numbers in the same sequence as

the source.

When recording from other sources connected

to the DIGITAL IN connector or a source

connected to the ANALOG IN jacks, do the

procedure below to mark track numbers

automatically. However, you cannot mark track

numbers automatically if the sound source to be

recorded is noisy (e.g., tapes or radio

programmes).

1 While the deck is stopped, press MENU/

NO.

2 Turn AMS (or press ./>

repeatedly) until “Setup?” appears,

then press AMS or YES.

3 Turn AMS (or press ./>

repeatedly) until “T.Mark LSyn(c)”

appears, then press AMS or YES.

4 Turn AMS (or press ./>

repeatedly) to select the setting, then

press AMS or YES.

When you select “T.Mark LSyn(c)”,

“

L.SYNC” lights up.

5 Press MENU/NO.

To Select

Turn on Automatic

Track Marking

T.Mark LSyn(c) (factory

setting)

Turn off Automatic

Track Marking

T.Mark Off

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony mds-je780 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony mds-je780

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info