Bedienungsanleitung Sony mhc s 3 (Seite 23 von 36) (Englisch)

158727

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Sound Adjustment

x Effect level (EFFECT)

Lets you adjust the “presence” of the current

surround effect.

x Wall type (WALL)

Lets you control the level of the high

frequencies to alter the sonic character of your

listening environment by simulating a softer (S)

or harder (H) wall. The midpoint designates a

neutral wall (made of wood).

x Reverberation (REVERB)

Lets you control the spacing of the early

reflections to simulate a sonically longer (L) or

shorter (S) room. The midpoint (0) designates a

standard room with no adjustment.

x Screen depth (S.DEPTH)

Lets you create the same sensation in your

listening room by shifting the sound of the

front speakers “into” the screen. This parameter

can be set to “OFF”, “M” (MID), or “D”

(DEEP). “D” provides the greatest amount of

screen depth.

x Virtual speaker (VIR.SP.)

Lets you turn the virtual speakers created by

the SEMI C.EX A, B, C sound fields off or on.

Adjusting the level

parameters

The SP. LEVEL menu contains parameters that

let you adjust the balance of front speakers and

speaker volume of the subwoofer. The settings

available in this menu are applied to all sound

fields.

1 Press SET UP.

2 Press P or p repeatedly to select “SP.

LEVEL”.

3 Press ENTER (A/V amplifier or remote).

4 Press P or p repeatedly to select the

parameter you want to adjust.

5 Press O or o repeatedly to select the

setting you want.

The setting is stored.

6 Press ENTER (A/V amplifier or remote).

See the table on page 34 for the speaker

level parameters.

x Front balance (FRONT)

Lets you adjust the balance between the front

left and right speakers.

x Subwoofer level (SUB W.)

Lets you adjust the level of the subwoofer.

x LFE (Low Frequency Effect) mix level

(LFE)

Lets you attenuate the level of the LFE (Low

Frequency Effect) channel output from the sub

woofer without effecting the level of the bass

frequencies sent to the subwoofer from the

front channels via the Dolby Digital bass

redirection circuitry.

• “0 dB” outputs the full LFE signal at the mix

level determined by the recording engineer.

• “MUTING” mutes the sound of the LFE

channel from the sub woofer. However, the low

frequency sounds of the front speakers are

output from the subwoofer.

x Dynamic range compressor (D.COMP.)

Lets you compress the dynamic range of the

sound track. This may be useful when you want

to watch movies at low volumes late at night.

• “OFF” reproduces the sound track with no

compression.

• “STD” reproduces the sound track with the

dynamic range intended by the recording

engineer.

• “0.1” – “0.9” allow you to compress the

dynamic range in small steps to achieve the

sound you desire.

• “MAX” provides a dramatic compression of the

dynamic range.

Note

Dynamic range compression is possible with Dolby

Digital sources only.

continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony mhc s 3 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony mhc s 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info