Bedienungsanleitung Sony minidisc player mds je480 b (Seite 12 von 31) (Englisch)

157194

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

masterpage:Left

(3 column)

lename[E:\SEM_Janet\Revision

ata\J9050000_4238553141MDSJE480CEL\4238553141\GB05OPE-CEL.fm]

model name1[MDS-JE480]

[4-238-553-14(1)]

Recording tips (continued)

Adjusting the recording level

You can adjust the recording level for both

analog and digital recordings.

1 Do steps 1 to 5 of “Recording to an MD”

on page 8.

2 Play the portion of the program source

with the strongest output.

3 Press LEVEL/DISPLAY/CHAR (or

DISPLAY) repeatedly until the level of

the input signal appears.

4 While monitoring the sound, turn AMS

(or press LEVEL +/– repeatedly) to raise

the recording level to its highest level

without turning on the “OVER”

indicators on the peak level meters.

5 Stop playing the program source.

6 To start recording, continue from step 7

of “Recording to an MD” on page 8.

Tips

• You can adjust the recording level by pressing

LEVEL +/– on the remote repeatedly during

recording or recording pause.

• Peak hold function freezes the peak level meters at

the highest level reached by the input signal.

1 While the deck is stopped, press MENU/

NO.

2 Turn AMS (or press ./> repeatedly)

until “Setup?” appears, then press PUSH

ENTER or YES.

3 Turn AMS (or press ./> repeatedly)

until “P.Hold Off” (factory setting) appears,

then press PUSH ENTER or YES.

4 Turn AMS (or press ./> repeatedly)

to select “P.Hold On”, then press PUSH

ENTER or YES.

5 Press MENU/NO.

To turn off the Peak Hold Function, select “P.Hold

Off” in step 4 above.

Note

The recording level can only be increased up to

+12.0 dB (for analog recording) or +18.0 dB (for

digital recording) (0.0 dB is the factory setting).

Therefore, if the output level of the connected

component is low, it may not be possible to set the

recording level to maximum.

Checking the remaining

recordable time on the MD

Press DISPLAY on the remote repeatedly.

For the information in stop mode, see page 16.

For the information during recording, see

page 8.

Monitoring the input signal

(Input Monitor)

You can monitor the selected input signal even

when you are not recording it.

1 Press EJECT A to eject the MD.

2 Press INPUT repeatedly to select the

jacks (connector) where the signal you

want to monitor is being input.

3 Press REC z.

When an analog input is selected

The analog signal input from the ANALOG

IN jacks is output to the ANALOG OUT

jacks after D/A conversion.

“AD – DA”

appears in the display during this time.

When a digital input is selected

The digital signal input from the DIGITAL

IN connector is output to the ANALOG

OUT jacks after D/A conversion.

“ –DA”

appears in the display during this time.

To stop Input Monitor

Press x.

Avoid turning on these indicators

GB02REG-CEL.book Page 12 Wednesday, July 13, 2005 2:56 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony minidisc player mds je480 b Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info